asa warping 3d models

Avoid lifting and warped prints!Print all three parts (body, cab, treads)Superglue the treads to the body.Superglue the cab to the body.Superglue works best for gluing it together.It will scale easily if you want a larger or smaller...

Avoid lifting and warped prints!There is a small amount of support needed - "for support enforcers only."Under the elevator shaft on the Middle Floor and Top Floor.The elevator door on the base floor.Increase the size of your “Dice Tower - Building...

Avoid lifting and warped prints!Print as many as you need!Rinse and repeat!Don't let them win! Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

This allows for easy loading and unloading of prints, as well as improved airflow, making it easier to remove warping from large prints. Additionally, the open frame makes maintenance a breeze, with easy access to all mechanical components. The...

S4 Avant Lighted LogoThis was a design I created as a retirement gift one of my best friends (lovingly nick named The Douche, no seriously, lovingly).  He had recently purchased an S4 Avant so I found this to be a fitting tribute to the...

The resolution/aspect ratio when streaming was also tricky to get to work correctly with my PC to remove "black bars" on the top and bottom of the screen and to fill the screen without having to use the "stretch" setting in Moonlight, which would...

Once the correct amount is placed (making sure you can still mount the motor), you can fix it by gently dropping some epoxy over it.You'll also need 8 pcs of neodymium magnets for the cabin/lid.8 mm diameter 3 mm thick, like these...

On the X tensioner, I made the narrow part considerably wider, stopping several tenths of a millimeter from the sides of the cavity it sits in in the X idler end, both to make it stronger and to reduce the play between it and the idler end....

I want to print higher temperature materials, minimise warping, failed prints and contain the gases released by those materials.This is my build log to enclose my modified Creality Ender 3. One motivation for this project is to gain experience...

Many new challenges popped up, because it will be different... ========================================== Printing & assembling Parts to print For the small (2V) geodesic sphere you have to print these parts: 2 x gs-2v-125mm_ring-01.stl 2 x...

Used a 25 loop skirt to minimize warping. Probe offset: X: -29.625mm Y: -6.3mm How I Designed This Credits and Hi-resolution gallery I was inspired heavily by this thing's design: https://www.thingiverse.com/thing:4610797 I modified the thing in...

Avoid lifting and warped prints!Print as many as you need!Rinse and repeat!Don't let them win! Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Avoid lifting and warped prints!Print as many as you need!Rinse and repeat!Don't let them win! Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Avoid lifting and warped prints!Print as many as you need!Rinse and repeat! Don't let them win! Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Avoid lifting and warped prints!Support enforcers are required for the hull and gun.Use “Adaptive Cubic” on Print Setting/Infill. It cuts off more than an hour of printing time! ...(it is already in the settings in the .3mf...

Avoid lifting and warped prints!Printed at 0.15 mm. ...It looks better when printed at that size.</li><li>Print out and assemble with...

If all lights are set to white with full power the clock uses 4 amps of current (20 watts), which is enough to create heat that is capable of warping PETG. Also if the clock is placed somewhere where the sun hits it, it will most likely get very hot,...

Less deformities in the tape is better as it will increase adhesion and lower model warp. --- --- ###### PowerBelt Belt Installation From the folks at PowerBelt: https://youtu.be/ShYZX8OavIs I will also note here that it can be helpful...

Ooznest • Low Profile M5 Bolt 21 x M5 Bolt 12mm (€5) 236 x M5 Bolt 15mm (€50) 46 x M5 Bolt 20mm (€10) 71 x M5 Bolt 25mm (€17) 12 x M5 Bolt 30mm (€4) 16 x M5 Bolt 35mm (€5) 18 x M5 Bolt 40mm (€7) 18 x M5 Bolt 50mm (€8) 44 x M5 Bolt 55mm (€18) 8...

I marked those files with “DNP” suffix (Do Not Print).I recommend printing the small parts out of PETG or ABS/ASA. Be generous with perimeters, top/bottom layers and infill.</p><p>The Hex Bodies are split halfway to allow printing on a 200x200x200 or...

ABS or ASA is fine as well but for long term usage and higher print temps, PC is best.This PA-CF should be a great option:Trianglelab Filament PA-CF15To summarize, print the parts in PC if you can to be on the safe side.Print all parts in 0.2 mm...

print with, so.... If you print almost everything in PETG with 2 mm shells, using 40% triangles infill, and print the blower nozzle in ABS using the lightest settings that still produce a usable part (since it needs the heat resistance and won't be...

If all lights are set to white with full power the clock uses 4 amps of current (20 watts), which is enough to create heat that is capable of warping PETG. Also if the clock is placed somewhere where the sun hits it, it will most likely get very hot,...