artillery sidewinder x1 ribbon cable 3d models

I put a little tape on each side of the clamp to help grip the cable. I also put a little dielectric grease on end of the ribbon to fend off corrosion which could also cause a hot connection. Print instructionsCategory: 3D Printer Parts Print...

I needed to secure the cable to prevent it from joining the ranks of burned out cables and connectors, a frustrating fate that many people have experienced. I also aimed to remove the cover since it serves no useful purpose, merely obstructing...

To prevent joining the ranks of those with burned out cables and connectors, I take extra precautions to secure the cable tightly. Removing the cover is also crucial as it only hinders airflow to the motor and complicates service. This mount attaches...

I don't require a lever or filament guide but I prefer the ribbon tension.

i dont need lever and filament guide but i like the ribbon strain

I'm thrilled with my Artillery Sidewinder X1, but there are two things that have me questioning its design. Firstly, the extruder ribbon cable lacks strain relief, which I believe is a major oversight. Secondly, I'm not sold on how Titan-style...

... The stock version without extra ribbon cable is called "Stock Ribbon Cable Support Artillery Sidewinder X1 v2.stl" with a weight of 7.4 grams. This design specifically fits V4 Sidewinders due to their distinct circuit board sizes on the extruder.

This is a handy component designed to alleviate strain on the x-axis ribbon cable of the Artillery Sidewinder X1. ...Simply slide it onto position and press firmly in place.

This is a small part that should help to reduce the stress that is put on the x-axis ribbon cable on the Artillery Sidewinder X1. ...Just slide it on and press it into place.</p> Category: 3D Printer Parts

Cover with protection for step motor, electric and ribbon cable support for artillery sidewinder X1

I designed these clips to help hold the ribbon cables on my Sidewinder X1. 9/12 Added a wide version of the Z-Clip for use when the ribbon cable is not centered on the post. ...The opening is 3mm wider than the ribbon cable.

I design my Sidewinder V4 without the cover so that I can clamp the ribbon cable as close to its connector as possible. This thing looked perfect at first glance https://www.thingiverse.com/thing:3945539, but when I printed it out, it didn't fit my...

This is a custom design of the ribbon cable clamp from SVANDRU, modified to also serve as a guide for the flat cable extruder.

This is a compact Ribbon Cable Clamp that securely clips onto the stock Extruder cover without requiring any modifications. You will only need two M3 cap-head screws and two nuts to install it. ...To add extra protection, I applied a strip of felt to...

I made the following modifications to create a more practical and visually appealing clamp: - I added a slot that allows for easy mounting without having to disconnect or reconnect the ribbon cable. - The mechanical strength of both vertical towers...

... The clips now fit the X1 V4 more securely. The ribbon is also held slightly better. As with the original design, this solution requires no screws and no refitting of the ribbon cable, simply print the clips and fit. ... TWO clips are required.

Passt an den Sidewinder X1 vom März 2021 Es werden zwar zusätzliche Gewindeeinsatz M3 und zusätzliche Schrauben M3x8 aber nur durch die dadurch erzeugte Anpresskraft kann sicher gestellt werden das die Zugentlastung auch wirklich eine Funktion hat...

the archive contains : V4 front version V4 version and higher version with original wires (vertical model 17 links) version with extended replacement wires (horizontal model 20 links less stress) the installation instructions necessary equipment: 17...

---- Cable stabilization for the ribbon cable on the Artillery Sidewinder X1. To snap into the original print head cover. ... ---- Printer brand: Artillery Printer: Sidewinder X1 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament brand: any...

Another cable support Artillery sidewinder x1

##3D Printed Parts 1 piece Artillery_Sidewinder_X1_Cable_Holder_Hotbed (PETG, ABS, or ASA) Support structure in contact with the pressure bed 1 piece Artillery_Sidewinder_X1_Cable_Hotbed_Clamp (PETG, ABS, or ASA) Support structure in contact with...

This Artillery Sidewinder X1 X Cover with Ribbon Clamp can take the strain off that flex point. New Clamp piece with Strain-Reducing Flange at no extra cost!!! STRONGLY RECOMMENDED: A. Inspect and smooth the mating surface of the two parts,...

Cable chain for Bed Cable for Artillery Sidewinder X1. It's not my idea, but I designed it completely my self. I got the idea from: https://www.thingiverse.com/thing:4710423 Credits to him. Be aware that if you use a BLtouch it can...

Part to fix the flat cable that goes to the extruder of the 3D printer Artillery X1 and avoid breakdowns in the connector. ... It is simply inserted under pressure, taking care not to damage the cable.

Parts to be printed to offset and protect the cable from the tray of the Artillery Sidewinder X1 3D printer. The machine is freed from the constraint of leaving space behind for the mobility of the cable (quite fragile, the silicone and fiberglass...

Valido para las Artillery X1 que tienen el cable de la cama a 41mm de la esquina más cercana. ... Unicamente he modificado el orificio por el que pasa el tornillo, agrandandolo para que entre la rueda de ajuste.

Heat Bed Cable support for Artillery Sidewinder X1 V.4 2 parts fit together to support cable where it enters the case. Do not need to open the case or undo wiring. First fit wiring and silicone sleeve into cylinder part with the cylinders lip side as...

I too run my Sidewinder x1 without an extruder PCB cover. I recently had a problem where the connector that holds the flat flex cable burnt out (This was an intermittent issue and kept causing thermal runaway errors and failed prints :[ ). I found a...

A simple cable strain relief, that can be added to the Sidewinder X1 without having to get the cable out of the connector (could make cable's and connector's life longer...). Simply unscrew the two screws holding the extruder cover, put left and...

It works only, if your printer can print accurately small parts. The needed clearance is 0.1mm! Please use other strain relief designs if you don't have a well calibrated or do not want to / can not properly calibrate your printer! ...But maybe you...