artillery sidewinder x1 e3d v6

I used his measurement and changed the screen size a little so that it fits more on Sidewinder X1 V4's LCD. I opted for the hinged design since I kind of liked it better. There are two cover files to choose from, the plain one is flat whereas the...

When I designed this, I had forgotten that the Genius stepper connector and BLTouch header are soldered on the opposite side of the board to the Sidewinder X1. To get it to work, I desoldered the original connectors and soldered in new headers on the...

This is a camera adapter mount for the sidewinder x1. For the version on the right: You will need 2x M4x28-30 screws with T-Nuts to mount this with the blue default plate for the pully mount. For the "left version": Just use a bit longer...

better fun duct for artillery

Artillery Sidewinder X1 left mount 5015 nozzle cooling fan duct release v5 will probably fit the Genius too, with mass close to 15g. Mounts to the heatbreak fan with original bolts, using two 3mmx20mm bolts with nuts to attach the fan to the duct.

Mainly Made for My Artillery Sidewinder X1, But Should Fit Every 20XX V-Slot Frame with "Nut 6". Made for Max. 100mm Extrusion. Filament Between Extruder and Caliper Must Have Tension Before You Begin. Ideal is to Clamp It Together and Extrude...

Artillery Sidewinder X1 Front Z Braces utilizing 0.5" copper water pipe. v8.1/8.2 The outer diameter of the copper pipe is 0.625". v8.2 (ONLY LOWER BRACES CHANGED) increased stiffness by restoring lower brace support on the bottom surface of the case...

The magnetic clamp is symmetrically, print the one piece twice. Edit: Added 16mm and 18mm version, depending on you caliper, a rounded knob and a bracket with blind hole for M4 Nut. Tool to calibrate you E-Steps properly with a caliper. Mainly made...

Very simple design I made to remove the spool holder from the Sidewinder top gantry to next to the printer rather, but using the original hardware from the X1's spool holder. All you need is a 20x40x200 T-slot profile. It slides into the gap easily,...

https://www.amazon.com/DIYhz-20Pcs-Position-Vertical-Switches/dp/B075RC6TFB?ref_=ast_bbp_dp It presses into one of the vents of my V4 Sidewinder X1. I'll solder small wires to the ends with some heat shrink to prevent shorting on anything. ... This was...

This is a 4mm PTFE hose adapter for the Sidewinder X1, allowing you to keep the filament roll off the frame. You can then use any spool holder without adjusting anything. (My printer sits on a higher table, making it impossible for me to place a...

Makes your Sidewinder X1 printer look fantastic with an abundance of vibrant colors. Simply program it. Picture quality may not be exceptional, but I assure you that it appears significantly better in person. Assembling the printer is relatively...

This is a quick and dirty mount for my Sidewinder X1 to hold the LED light bars sold by MYPLUS on Amazon. This is a great little touch light I have under my desk and wanted to add to the printer. It lets you mount the light facing down from the top...

This system is designed for the Sidewinder X1 without any modifications, covering the left side of the x-axis. It fits perfectly and provides a secure hold due to the profiled snap. The design is mostly thin-walled but stable, making it efficient...

This is a quick and dirty mount for my Sidewinder X1 to hold the LED light bars sold by MYPLUS on Amazon. This is a great little touch light I have under my desk and wanted to add to the printer. It lets you mount the light facing down from the top...

One is designed for front mounting on the X1 Sidewinder (https://www.thingiverse.com/thing:4257585/) and another one is suitable for the CR-10 or any other printer that uses 2020 or 2040 extrusions for the frame...

You might need a longer M3 screw. The PTFE hose is simply inserted from behind. You can adjust the scad-file for your preferences. V2 is a little bit stronger and might be printed with less support. Das ist ein Adapter für 4 mm PTFE-Schlauch, damit...

Heavy filament spool on the Sidewinder X1 above was never a good idea (print quality was worse on taller parts, etc.) Also printhead kept pulling up slightly.This PTFE tube holder helps to avoid the problems and just leave the filament spool next to...

remix of allieprice afterburner mod for sidewinder, firmware N/A

Supports for Z-axis stabilizer bar of Artillery X1 Sidewider. Use the screws on the printer for anchoring. It is necessary to remove two screws from the bottom cover of the printer for placement. Then screw in parts A and B with the screws removed...

Secure it with the leveling wheel. Print Settings Printer: Artillery Sidewinder Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA Notes: I strongly suggest to print in PETG for more temperature resistance Category: 3D...

This is a cover for the right-hand side X axis.\r\n\r\nCRUCIAL NOTE!\r\nThis cover will only fit a version 4 Sidewinder X1 model.\r\n\r\nI used Cura 4.4 to generate the slicing code for this part.\r\nFirst, flip it over and since it's a small...

The shape fits for the Sidewinder X1 carriage and assures it is not running into the end stop during homing. Other printers might need amendments. Be sure to use a 24 V fan and check the polarity on the connectors as fans my replacement fan came...

Designed a mount for my Sidewinder X1 as I had the LCD screen running OctoPrint/OctoScreen on the table. The support is designed to use the mount sold with the screen. Screen is:...

I tried many different covers on Thingiverse for my Sidewinder X1 and didn't want to use double-sided tape or any adhesive so I was heavily inspired by another model here on Thingiverse but instead of editing his design I designed one myself, taking...

I spent hours searching for a filament guide that would fit the stock extruder on my Sidewinder X1, but I couldn't find one that matched. Most models were either too small or too large, so I decided to take matters into my own hands and create my own...

One for side mounting on the X1 Sidewinder (https://www.thingiverse.com/thing:4064724/) and one for the CR-10 or any other printer that uses 2020 or 2040 extrusions for the frame (https://www.thingiverse.com/thing:4064715/). Key Features: Solid...

Works great on my PKM8 and now also on the Sidewinder X1. Then you need a M3 grub screw and a rubber band, then you can start... The small cap needs to go onto the measureing sensor to prevent it from scratching the bed. The measurement is pretty...

... It functions perfectly on my PKM8 and now also on the Sidewinder X1. Then you need an M3 grub screw and a rubber band, then you can start working... The small cap needs to be placed onto the measuring sensor to prevent it from scratching the bed.

Works great on my PKM8 and now also on the Sidewinder X1. Then you need a M3 grub screw and a rubber band, then you can start... The small cap needs to go onto the measureing sensor to prevent it from scratching the bed. The measurement is pretty...