arrow 2 antenna 3d models

This is for mounting the Arrow II Portable Antenna boom to W5AIR Round Extrusion. Combined with other parts in this series and bostwickenator's slew drive, you can have a rotator for your portable yagi antenna. This mount was designed for the width...

Allows attaching the "Arrow" ham radio satellite antenna to a tripod. Consists of a cradle into which the boom of the antenna is placed, then held with zip ties. Has a triangular/pyramid type end which fits into many tripods. This allows you to...

This is a rotatable mount for an Arrow Dual Band Yagi antenna with a 20mm square beam. Normally this antenna is hand held but can cause fatigue. This mount allows connection to a photo tripod with a loose ball head. This allows active orientation...

This can be used by amateur radio operators who want to use their Arrow satellite antennas with a rotator such as the Yaesu G-5500. The cross boom I used is sold as 1-1/4" fence top-rail. The mount clamps to the 3/4" square aluminum boom on the...

This holder will hold either the VHF or the UHF elements on your arrow antenna boom. I typically for space considerations remove all of the elements and store them on the boom holders. When deploying I only store the VHF elements on the holder and...

I wanted something simple to keep all the parts of my Arrow antenna together. I was shooting for something that would keep all the parts in a cylindrical shape without anything protruding so it could fit in a PVC tube for storage/transport. This is...

Prototype antenna mount for rx and tx on a rdq arrow frame.

Super Basic mount - Print two of these to hold the 2M elements against the Arrow Satellite Antenna for Storage.

This is a mounting system to mount an Arrow Antenna on a tripod. The use of inner and outer sleeves allows the antenna to be rotated approximately 90 degrees in either direction. Hopefully, it will prove useful to someone! Print the following: 2 x...

To be able to store the Arrow Antenna safely without necessity to deassemble, I came up with this small hook which can be attached to the front element of the antenna. With this hook you can store it long or short term out of reach of children or...

This is a custom antenna mount for the FliteTest Mighty Mini Arrow. Its primary purpose is to allow an MMCX connector to pass through while securing it in place with zipties, which are then attached to the antenna itself. Without this attachment...

The Arrow II antenna is perfect for working satellites with your HT ham radio but it's difficult to hold both the antenna and the radio at the same time. Also, the Arrow antenna is front heavy. ...This gives you a mount for your HT and helps balance the...

This is used to fix my arrow antenna to the 1/4-20 quick shoe plate on my tripod and stops it from rotating vertically when the antenna is twisted from horizontal to vertical polarization.

The Arrow II antenna is perfect for working satellites with your HT ham radio but it's difficult to hold both the antenna and the radio at the same time. Also, the Arrow antenna is front heavy. This gives you a mount for your HT and helps balance the...

Modify your Arrow antenna into an ultralight, packable antenna In my quest to reduce pack and radio weight, I have been slowly modifying my Arrow antenna over the years.  Having operated in nearly every type of summit weather I came to the conclusion...

These clips fit snugly onto the shaft of the Arrow II 146/437 antenna, efficiently managing RG58 cables. There are three distinct parts: The solo clip, designed to hold one RG58 cable securely; The Dual clip, expertly crafted to manage two; and a...

This is a clamp designed to attach a Fairview Microwave SA35100 attenuator to an Arrow Antennas 121.5-3 direction finding antenna for Search and Rescue (SAR) use. I designed this to be able to accept a velcro strap to apply pressure to the...

I required new endcaps for the gamma matches on the Arrow satellite antenna, so I engineered replacements. For some reason, the one I fabricated for 70cm didn't fit the 2m side, necessitating adjustments to the dimensions for the 2m version. ...The...

This mount allows you to connect a tripod → arrow antenna → cellphone. Two prints of this model are required. It uses 4x M3 screws/nuts to clamp the two pieces together, and a ¼" nut on one print so that it can mount to your tripod, and a ¼" bolt on...

This is an adapter to mount the Arrow II U/V antenna to a camera tripod. I added my call sign to my final piece. Printed using the pretty PLA 4.1.5 profile with its default settings. This should work with any 1/4-20 tripod mount. ...I also printed a...

While these clips are specifically designed for the Arrow II 146/437 antenna, they may also be compatible with other models. However, thorough testing is recommended to confirm functionality. Before inserting cables into the cable guides, it's...

2 inch high profile arrow vanes

You will need to create several custom components to attach your Arrow II Satellite Antenna to a tripod. First, you'll require an HT mount, one minimal unit is sufficient. Next, get three enhanced Arrow II mounts. A steel flat piece with dimensions...

A Blender 2.79-created 3D arrow model is available in this archive, compatible with several formats such as .blend, .3ds, .fbx, .ply, .x3d, and .obj. To render using default Blender 2.79 settings, simply double-click the left mouse button to open the...

I crafted a sleek seconds simple arrow pendant utilizing Tinkercad's intuitive design tools. ...The pendant features an elegant arrow shape, precision-crafted to perfection, which adds a touch of sophistication to any outfit.

An Arrow model has been designed using Blender 2.75 software. It can be applied for broadcast, high-res film close-ups, advertising, and design visualization purposes. The model consists of six distinct objects and is intended to be subdivided. At...

Arrow Rest - Pfeilauflage zum Aufkleben Print Settings Printer: Flashforge Dreamer Raft Options: No Raft Required Support Options: Enabled Resolution: 0.20mm Infill Density: 100% Solid Infill

I designed a straightforward arrow-shaped ring using Tinkercad's intuitive interface, taking only a few minutes to create and refine. ...The model features a sleek, modern aesthetic that can be easily customized with various materials and colors.

A 3D-printed sign featuring an arrow is created with specific dimensions using a customizer app on Thingiverse, a community for designers to share their models. The following settings are used: Text: The sign displays an ARROW. Dimension: The arrow's...

I found them on eBay UK at the following links: http://www.ebay.co.uk/itm/12pcs-Aluminum-Arrow-Connection-Inserts-Repair-for-Broadhead-Archery-Practice/291831522504?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649...