arrma typhon 3s wing 3d models

These rear diffusor splitter add-ons are a perfect stylish and practical addition to your ARRMA Infraction 3S BLX/Mega platform. These splitter add-ons for the rear diffusor add downforce to keep your car on the ground and also look stylish while...

I replaced front suspension A-Arms for my Arrma Granite 4x4 3S BLX with these, and they might also work with other Granite models but I haven't checked yet. A beefier version is included that fills in the inner triangular holes to strengthen the part...

These side exhaust pipes add awesome muscle car styling and looks to the ARRMA Infraction 3S BLX/Mega platform. Beware, these pipes make the Infraction a lowrider and they will scrape the ground on bumps over five millimeters or so. Because of this,...

Arrma Granite 4x4 BLX owners who have installed the Arrma 4S Tower2Tower center brace will find this guide helpful. This part has been designed to stand at 2cm in height, so you should first measure the exact distance needed and then push through...

... if you want, Traxxas have same 46t spur all from metal. Gears oryginally are used on Traxxas E-Revo, and Xmaxx, so they should stay long in 1/10 Arrma. You need to slightly modyfy gear, by cutting internal walls, so you can fit clutch pads. ...

Hello this is a reproduction of the **front only body mount** of the [MT BODY MOUNT SET AR320404](https://www.arrma-rc.com/part/AR320404) part. This must be printed with a flexible filament. Note that there is only one position (one hole in each...

Repair for Arrma Granite body shell. ... Requires M3 bolts and nuts to fix the top and bottom repair plates. If fitting the rear wing - use magnets in the recesses.

Scaled down to 4" wide to replace a cracked polycarbonate rear wing on the Arrma Vorteks Voltage 2WD. ... Didn't move the mounting holes, so you will have to drill your own, I believe they are 86mm on center.

Hey, i invented a stronger Version of the Arrma Rodend for the Shock Absorber. It works on the 1/8 scale models well. Let me know, what is your experience! Printing without filling, only with walls so it´s 100% stable. ... My first Projekt on...

Problems with the screws breaking that hold your wheelie bar / wing on your ARRMA Kraton s6? 3D print this support which strengths up the wing. Prints very easy with no supports and at a layer height of 0.3 with 30% or more infill for strength.

This is my V1 of the Arrma Kraton GoPro Mount on the Wing. The stock screws are too short, at least mine were, so I swapped them out for AR721316 Button Head Screws, M3x16mm. When installed, it's a bit stiff to mount the GoPro. ...If any issues arise,...

I couldn't find any good mounts except for one wing mount for the Kraton (Which can be found here: https://www.thingiverse.com/thing:4781582). So I designed this for my Talion. Notes: This design uses M3 screws and nuts to connect to the wing...

They typically come in sets of four pieces (front FF, FR and rear RF, RR) but I just need one, specifically the front right piece, so I opted to make it myself. It's the suspension mount located behind the differential of the front axle, as you can...

Copy made of original part Arrma kraton exb 6s. ...Fits perfectly.

Arrma Infraction Pro Stock Drag Wing This is still a Work In Progress, but I think the Infraction looks even better with a drag style wing. Since there aren't any factory-made ones that caught my eye, I decided to try designing one myself. It's...

As promised, the Runcam 3S holder for the Sonicmodell AR Wing and RMRC Recruit is now available. To get started, you'll need to make sure the foam cap fits snugly around your camera, as the 3S model has a slightly wider profile than the Gopro...

As promised, the Runcam 3S holder for the Sonicmodell AR Wing/RMRC Recruit. You'll have to make the foam cap fit the camera, since the 3S is a bit wider than a Gopro Session model. ... I've printed mine in PLA, but TPU will do too.

This is a remixed version of the ARRMA KRATON 6s, tailored specifically for the 8s model. Note that this is still a work in progress. I created this remix to accommodate the Maginon Action camera (link below). To get it to fit properly, I had to...

... a Wing and Mount that I made for the Felony. ...The stock body without wing left a lot to be desired. It looks amazing now. It's 230mm and fits the Felony very well. ... My YouTube Channel: https://www.youtube.com/channel/UC_FQwdP4veayQQa694qWi_w

The pro stock drag wing by designer "magnetik" is awesome. ...I wanted to fill the holes where the support rods go so I made these little plugs to fit.

ARRMA 3S F1 STYLE WING MOUNT LED 9MM LED LENS PRINTED IN TRANS ORANGE

Based off the motor support by hyperion917 on Thingiverse I wanted to make some changes to both for printing and function improvementI got rid of the tab for the 4mm screw so it could print flat and made a new way for the zip tie connection to work.

A remix of the original by schneidp20, thank you. as suspected by the author too soft with TPU so added a middle section to stiffen the part. having tried many fillers this one gives the same stiffness as the stock part. Print with 20% gyroid...

Made this in TinkerCAD because I was sick of my axles popping out of place when I did jumps.

These are adapter knuckles and C-Hubs for using Arrma 4S stub shafts in a 3S car (so you can run 17mm hex and wheels). The 4S stub shafts are slightly longer than the 3S ones. This mod widens the car very slightly because I adjusted, just not...

Rear Wing Mount Upgrade by Arrma Engineers Talion owners now have a proven way to boost their car's aerodynamics with this game-changing Rear Wing Mount system from Arrma. Part #AR320379. ... Engineers at Arrma designed this clever upgrade to secure the...

Heat fills gaps perfectly now\nPrint Preferences\nPrinting Device:\nThe K8200 printer is selected here\n Infill Density:\n Set to twenty percent.

Just a quick Wing adapter I made to be able to mount the Armma Kraton rear wing on my 1/5 scale Losi DBXLE 2.0, I just did it because I like the look of the Arrma wing. ...looks to be about the same total surface area, just a little more compact due to...

Just a quick Wing adapter I made to be able to mount the Armma Kraton rear wing on my 1/5 scale Losi DBXLE 2.0, I just did it because I like the look of the Arrma wing. ...looks to be about the same total surface area, just a little more compact due to...