arrma kraton 4s v2 3d models

Arrma blx 185 mount plate

Arrma infraction front wheel louvers.

Mudguards for the Arrma Mojave 6S V2 / EXB. Two versions: One pair with "Mojave" print and some blank ones. Works with Scorched RC Fenders. Print in TPU, use M3x6 or M3x8 to attach them. ... Send it!

body posts for stretched typhon using kraton chassis.

Arrma Granite gimbal guards with rislans.

Arrma Mojave Front Bumper Mount TPU

XLX2 mount works with Arrma Typhon and stretched Arrma Typhon (I used Kraton chassis on mine), or any other Arrma 6s vehicle where the servo is not sitting in the chassis the long way (like the Talion), and does not use the upper chassis support...

... truck. ...It enables you to run high-torque motors at 32P without needing to switch to the 3BLX slipper clutch setup. The V2 model features a precise shape that perfectly matches the slipper clutch pad, ensuring optimal performance and reliability.

I used the front design found here: https://www.arrmaforum.com/threads/3d-printable-front-bumper-for-3s-4s-rigs.20929/ To install, remove the three screws holding the front suspension hanger (be careful not pull out the pins) and the two screws that...

flexible bumper made with TPU 95A for arrma 6s

Just a simple composite ball for the Arrma 6S shocks.

Arrma Mojave mesh window attachment with cable ties

these are skid plates for an arrma granite v3

Replacement tie rod end for Arrma 4x4 3s BLX.

Used with stock arrma screws. ...I used ABS.

Here's a Quick design I mocked up for protecting the LiPo on my BeeRotor X200. It would likely work well for other 'X Frame' quads where the battery hangs underneath. The BeeRotor X200 has two LiPo straps instead of one, but most LiPos are too short...

Customized Version of http://www.thingiverse.com/thing:348618 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=348618 Instructions Using the following options: Battery Height Set to 48 Band Hole...

These are decorative inserts for Arrma's Backflip wheels. They fit both the 4S and 6S Backflips. They fit into the triangular recesses in the wheel face. You will need to print 5 per wheel and glue them in place. There are two versions - one...

Just ARRMA Mojave 6S window net, but your ARRMA will look like more realistic and your crew will feel more safe :-)

... a great choice, offering protection and convenience for your high-performance RC vehicle. ...This cover set is designed to be versatile, making it suitable not only for the Arrma Typhon V4 but also for other ARRMA models that require similar coverage.

I used the front design found here: https://www.arrmaforum.com/threads/3d-printable-front-bumper-for-3s-4s-rigs.20929/ To install, remove the three screws holding the front suspension hanger (be careful not pull out the pins) and the two screws that...

Arrma Raider Shock Tower Item Print Settings Printer: K8200 Infill: Ten Percent

this is a front grill for arrma infraction that will hold 17mm light (no glue needed)

Check out the ARRMA Typhon BLX 6S mudguards - a must-have accessory for off-road enthusiasts!

Arrma Granite plugs below servo to avoid dust and rocks entry from there.

Raider Steering Servo Mount by ARRMA Print Options Printer: K8200 Infill Rate: Set at 10 Percent

RC GANG 93 Protection for the rc 1/10 ARRMA GRANITE 4X4

RC GANG 93 Front grill for ARRMA GRANITE 1/10 RC Monster truck

Hood protector for the Arrma Big rock designed for M4 dome hex screws

Arrma Limitless Hammerhead Front Wing Here is a video: https://youtu.be/KuofdArAWRU