arrma granite voltage servo 3d models

Scaled down to 4" wide to replace a cracked polycarbonate rear wing on the Arrma Vorteks Voltage 2WD. ... Didn't move the mounting holes, so you will have to drill your own, I believe they are 86mm on center.

Designed a front suspension hanger for my Arrma Graphite Voltage. I needed this for the custom bumper I created (https://www.thingiverse.com/thing:5293607). ...Thought the hanger might be helpful to someone if their part breaks for if they want to...

Raider Steering Servo Mount by ARRMA Print Options Printer: K8200 Infill Rate: Set at 10 Percent

Designed a front suspension hanger for my Arrma Graphite Voltage. I needed this for the custom bumper I created (<a href="https://www.thingiverse.com/thing:5293607">https://www.thingiverse.com/thing:5293607</a>). Thought the hanger might be helpful...

This servo mount gives you a place to install an ESC into the Arrma Grom when replacing the stock ESC/receiver unit. ...Reuses all stock hardware.

Made this to help the small fan utilise the entire heatsink and not just the small area it sits on. Fits right under the fan itself using Original Fan screws. ... Upper pillbox was made to prevent gravel from my local track jamming the fan up and...

!!!!! Warning attached stl is partial only !!!!!!Support me by getting full model for free from here (it only takes two clicks) https://makerworld.com/en/models/148762#profileId-162371I wanted lights for some night bashing….To connect to receiver...

AR330469 - STEERING BLOCK Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports...

I removed the logos of the aileron that required support and would not print well with 0.8 nozzle.

Customized version of https://www.thingiverse.com/thing:4381135 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4381135

Vis M3. ...

Hides the interior of the vehicle at the rear, protecting it from dirt.

Vis à utiliser diamètre M3 Filament TPU

Vis à utiliser : diamètre M3 Impression à l'envers avec support . ... Filament TPU

Utilisation de Vis M3 tête fraisé. ... Use of M3 fresh head screws.

Arrma Granite 4x4 BLX owners who have installed the Arrma 4S Tower2Tower center brace will find this guide helpful. This part has been designed to stand at 2cm in height, so you should first measure the exact distance needed and then push through...

Quick remix to make this great ESC holder bolt directly to the lid of the radio box of the Arrma Granite BOOST 4X2 brushed 2-wheel drive truck. =================================================================== ORIGINAL ITEM ...

For the [Arrma Granite 3S BLX v2](https://www.arrma-rc.com/rc-cars/2019/granite/blx/4x4), the following **issues** of the above "thing" have been fixed : * Space between holes that goes around the body post towers was too high, so I reduced it to...

For the Arrma Granite 4x4 3s, but It might work with other Arrma cars that use part ARAC3444. ... Also requires this Metal LED Strip and should be a press fit/glue fit: ...

The differences are : * Tougher support (because I broke the previous one on a bad landing) * Needs shorter screws * Has dedicated holes to insert nuts under the wing * I pushed the wing back by 4mm because it was to close to the body for some I...

I wanted to hang my new Arrma Granite 1:10 on the wall, and couldn't find anything, so I whipped this one up. It hangs on either the front or rear control arms, vertically.This is v2, and it's holding solid. I printed with 6 walls using ASA, but do...

I replaced front suspension A-Arms for my Arrma Granite 4x4 3S BLX with these, and they might also work with other Granite models but I haven't checked yet. A beefier version is included that fills in the inner triangular holes to strengthen the part...

This bracket provides a place to mount a 40mm cooling fan, an aftermarket ESC and a receiver on an Arrma Granite Voltage. Super glue the antenna bushing into the lid from the bottom after printing. Lid is held on by 2 body clips. Update 7/5/21. ...I...

Hello this is a reproduction of the **front only body mount** of the [MT BODY MOUNT SET AR320404](https://www.arrma-rc.com/part/AR320404) part. This must be printed with a flexible filament. Note that there is only one position (one hole in each...

The Granite Device Servo Drive, model VSD-E-160, is a cutting-edge piece of equipment designed to provide precise control and efficient operation for various industrial applications.

My antenna cover broke from the base, so I designed this to go over the antenna wire. ...It is held into place with some glue or some bluetack

ARRMA Steering Posts and Servo Saver AR340004 Hab noch die Zeichnung beigefügt um die teile, sich aus Stahl oder anderen materialen zu fertigen. ...

Arrma Raider Steering Servo Mount (B) Unleashes Your Printer's Full Potential! Print Settings Revealed Printer Powerhouse: K8200 The K8200, a force to be reckoned with in the world of 3D printing, brings forth unparalleled precision and speed.

Futaba S3051 HV high voltage servo with cross plate

Busted a linkage recently and found myself facing a problem - the local hobby shop was all out of them. Rather than wait around, I decided to take matters into my own hands and designed this one from scratch in Tinkercad. Replaced all four links with...