arm for webcam 3d models

Make sure you print the stand with the flat side of the ball facing the build plate. I used one of the screws and nuts from my gopro like the on in the picture. You need to find information online on how to disassemble the webcam to change out the...

There should be enough space for a reasonable bend.Notes:If there's too much slack in the cable for your taste, just carefully feed more cable into the leg, while pushing the base part in the hole.Make sure that the exit hole is big enough, so you...

There should be enough space for a reasonable bend.Notes:If there's too much slack in the cable for your taste, just carefully feed more cable into the leg, while pushing the base part in the hole.Make sure that the exit hole is big enough, so you...

... holes fit perfectly into the original Stuva board holes. To get started, you will need: 2 x 3.5 x 16 wood screws for the baseplate 1 x M5 x 16 screw with nut for connecting to the arm 1 x M3 x 20 screw with nut and washers for securing the cam

A mount for a cheap USB webcam (see picture) that sits outside of a transparent enclosure. In my case it's for a Voron2.4 and does the Job as a decent monitoring cam without having to worry about routing USB cables inside your chamber. Not the best...

Directly replaces mounting bracket on Logitech 9000 webcam using same screws and pivot rods. Also uses one 3mm screw to attach the cover to the base. Choose either the vertical or horizontal mount depending on which way you want the bracket to...

Webcam phone holder designed to detach from monitor when not in use.This design is intended to be use with Camo. Use double sided tape to connect to the monitor. ...and feed cable through the centre hole.&nbsp;<br><br>Note: This model is a work in...

Thus it is possible to use his camera with 1/4 inch connector as a webcam on the computer. You need: -The 3D printed part (adapter) -A ball head joint with 1/4 inch connection (female at the bottom, male at the top). ... -1/4 inch screw -M3x12...

Logitech C270 mount designed specifically for FlashForge Creator Pro and similar 3D printers, thoroughly tested on the FFCP. This design was a game-changer because it allowed me to position my camera just like I'm actually watching it. Plus, someone...

I originally developed a chassis for an $8 Fosmon webcam to be mounted on my Rostock Max: http://www.thingiverse.com/thing:1349752. However, while this solution worked, the quality really wasn't that great, and I began searching for something else. ...

My sweet stash of neglected electronics had an old Logitech webcam that I wanted to utilize. I also had some super-tiny little stock X-axis 8mm rods that came original with my Printerbot 1405. Based on that, I devised this speedy design. It's not...

This mounts a Nexigo N60 Webcam to 2020 aluminum extrusion (will need 2x m3 tnuts and screws) while still letting you use the ball tilt feature. I designed it to aim the camera 60 degrees downwards, so I could mount it to the top-front-middle of my...

A bracket that simply clips into the extruded channel of the Sovol printer for easy attachment, and therefore eliminating the need for bolts as in the original design. The two are joined together in a "Go Pro" style joint connector using a...

This is an adjustable webcam mount for a Creative Live! Cam Sync HD which can be rotated and height adjusted. I'm using it for my octoprint installation to supervise the prints.Print each of the stls in the given orientation. I've used PETG for all...

I don't really know how to use tinkercad but I made this to use with my webcam.Parts:1x M3x12 bolt from spare parts1x M3 nut from spare parts1x D-ring camera mounting boltInstructions:Pre-tighten the bolt and nut to get the nut to stay in the seat...

... causing an interruption. I have tried others, but none work near as well as this model.</p><p>Designed in Fusion360, and sliced with PrusaSlicer. Used Prusa orange PETG for effect, but not necessary. ...No supports, brims, supports needed.</p>

I designed this for compatibility with an Ergotron monitor arm; depending on the geometry of your setup you may need to adjust significantly. Print instructionsThis is designed to print with the large flat bottom area against the build plate. The...

The hinge fits together without any hardware but I used a 35mm M3 bolt and a nylock washer to get the tension just right so the cover stays wherever you put it.&nbsp;A small bump on the inside of the arm contacts the body of the camera and prevents...

Remixed for Acer Predator Helios 300 (2020)

Needed parts / preqs:SHCS M6x16  screw for the webcamxHCS M5x10 for the mount(Spring) Nuts for your frame.Use a stiff filament From tinkercad, so no step file. ...just ask if i can help you with anything.

Camera cover for the iMac 24 inch released in 2021. ... Credits for the idea and logo go to https://www.thingiverse.com/thing:4818148

I liked the modular camera mount but I wanted for the other side so this is

This is an upgrade kit for my Anet A8 3D printer camera.

Here are STL files for an ODROID camera mount that can securely hold micro servos.

Loved your design Teaching Tech, but as I use a Gopro for my Octoprint camera, I made an easy mount for it that fits your design :-) Category: 3D Printer Accessories

I'm really impressed by your design for Teaching Tech, and since I use a GoPro for my OctoPrint camera, I created a simple mount that perfectly complements your design.

Remixed for notebook Acer Nitro 5 (2023) that has a little green led on the side of the camera.

I remixed this for a friend so that it would fit the notch on the 2021 MacBook Pros. ... Enjoy!

Really like the mounting bracket daedalus1982 made for the MK3 which I've been using but also wanted something similar for the Prusa Mini but couldn't find one. Decided to take his design and make it work for the Mini so that it I could use...

Just reinforced this fantastic base for my c270 to enhance its overall stability. ... The camera sits comfortably inside, perfectly secured in place.