arduino 3d scanner photogrammetry

Just to make it easier finding it all in one place.No support required.Diesel Generator you will need to superglue the bottom frame (very simple)Designed on...

Hunt them down and make them pay!Shelter yourself! Deliver your cargo!Stay in the fight!Super glue works best.Resize for smaller or larger use.Clean your build plate with dish soap to ensure the floor of the Modules do not lift off (long...

It can hang off the plywood deck (¾ inch") or the slightly thinner shelving above. Support enforcers are neededNo gluingEasy to printDesigned on...

If you don't own a 3D printer but have seen this blank somewhere else and want to use it, I recommend just asking in a furry group chat on a platform of your choice. Many furries are also tinkerers and may print this for little money.</p><p>The base...

... layers, 60° bed temperature, outside perimeters first. &nbsp;I turned the model 35° anticlockwise, then set the seam position to ‘rear’. &nbsp;The texture on the side panels comes from this textured bed plate, and I used the Tecbears black PLA.

You only need the USB board and the motor to make it run.This was specifically made for making interactive 360 photos of 3D printed objects quickly, using video (takes about 10min), but it can also be used for making animated gif's, rotating objects...

Remove the stock z-axis tops and replace with this light bar mount.Dual Mount Z-Axis Top No Switch: Same as Dual Mount Z-Axis Top with no hole for the power switch.&nbsp;&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill:...

This is a followup to: Lack Attack#3: Koppla the Lack: https://www.prusaprinters.org/prints/15919-lack-attack-3-koppla-the-lack-aka-power-the-lack-s without further adieu.... Attack 4: ENCLOSE THE LACK Its been a while since my last update, mostly as...

I present to you, what is likely one of the only mechanically working 3d-printed Prop Revolvers available, especially for free!Go here to see it in Operation: https://i.imgur.com/DBUVUkF.gifvIt is quite well balanced, see here:...

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

I've spent quite a bit of time getting to this design and I want to make it as accessible as possible so that as many people as possible can enjoy the greatness that is easy loading/unloading of the MMU. Good luck and enjoy!! Print Settings Printer...

It's yours to make!).Stand up your Space Port before it's too late!&nbsp;More Space Port!Space Port - https://www.printables.com/model/205432-space-port-terrain&nbsp;Space Port Living Quarters -...

The modules with the lid are great for tall objects (remotes, bottles) while the lift modules are perfect for coasters or other small objects that you wouldn't want to reach in too deep to grab.I also wanted a project that would challenge my limited...

NASA 3D resources. Homunculus Nebula - 3D model display stand Other astronomical objects Object Scale [1:x] K = 103 (thousand)M = 106 (million)G = 109 (billion) Image Inner Solar System Mercury 20M, 60M, 120M Venus 60M, 120M, 250M ...

You will need to source longer M5 screws.&nbsp;Change Log:8-Dec-2020: Added MINI Light Bar Flat version5-Jul-2021: Added MINI Light Bar Spare HW version&nbsp;&nbsp;Print instructionsRecommended Print Settings:Filament type: PETGLayer Height:...

I've read that brushing or submerging in melted candle wax (not too hot though - Paraffin starts melting at 37 deg C / 99 deg F) can seal a 3d print. If you do use wax keep fire safety in mind as some FDM plastics are flammable and wax has now made...

Ihr müsst die Kabelfarben dazu in der Reihenfolge umdrehen:Blau-Rot-Grün-Schwarz --&gt;&gt; Schwarz-Grün-Rot-BlauDanach noch den Drucker Kalibrieren zwecks ausgebauter Pinda und##################### FINISH #####################oberster Stecker auf...

If you don't find an answer to your question here comment below or submit an issue on project's GitLab.Note: All parameter names used here are names from the Customizer menu. If you are looking at the source code, just replace spaces with underscores...

The sound of the 3d printed gajda is very close to that of a wooden one – I'm not even sure I can hear the difference.All the Bits and How to Print ThemThis project has many pieces. It includes everything needed (other than the bag) to create a...

Po cca 10 letech zkušeností s&nbsp;kutilsky vytvořeným prostorově úsporným pisoárem pro malé bytové WC (nejprve kompletně z&nbsp;nerezového plechu, oceněno v&nbsp;soutěži pořadu Vychytávky Ládi Hrušky, později vytvarovaného z&nbsp;akrylátové desky)...

These models were heavily modified to fit in the arms' surfaces, using Microsoft 3D Builder. Some parts were designed to be self-assembled, so the resulted articulation may be too loose. Do not scale unless you find it too loose or tight. If you just...

I plan on converting the whole station from spare parts to all 3d printed. Even though it doesn't show in the schematics, some of the sensors are doubled for redundancy and to check each other. Updated 8/17/18: Since the original I made back in...

This model was based on Naidu (2020), remeshed, scaled and divided using Microsoft 3D Builder. The shape of the satellite Dimorphos is just an ellipsoid that fits the radar images. The next year we will have better images from this pair from the DART...

I did not render this model, I just resize, soften and simplified it using Microsoft 3D Builder, to share the same scale as other objects. The original file is from the collection of asteroid radar detection of the PDS site.<br> The file's names...

Dragon and Mosquito use the same length of PTFE tube which is why they share jig.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress and Banggood. Shipping takes a while from China but quality is excellent and...

I start by drawing different views of a 3D object in CAD, convert the files to DXF, and bring the files into Fusion 360. Most of my drawing occurs outside of Fusion.</p><p>I made multiple versions of the gameboard segments, the various accessories,...

I made the main body with SolidWorks 2018 and the details with textures I made up, processed with MATLAB R2020a, and finally mixed using Microsoft 3D Builder. I don't like very much flying saucer designs, but I really enjoyed the show. The bottom...

I did not render this model, I just softened and simplified the non-convex model available in the 3D Asteroid Catalogue site, where it is unreferenced, but I think that it is from Hanuš (2017). All three moons of it are too small to make in the same...

There are other lightweight extruders available but mechanically I consider the Orbiter to be the most capable option.What to print:Print these...

There are other lightweight extruders available but mechanically I consider the Orbiter to be the most capable option.What to print:Print these...