arducam raspberry pi 3d models

... She customized it for her Arducam camera based on available information. Credits: https://www.thingiverse.com/thing:4446024 A like is appreciated and can help with referencing! Post your makes, and don't forget to check out my other designs!

Protect, mount, & aim your Arducam IR camera on your 3d printer! Designed for mounting to either 20x20 or 30x30 extrusion, but would work mounted to a flat plate, as well. This is specifically designed for [this...

Adapter for the raspberry pi arducam. Base has a hole that will need to be tapped 1/4-20 for a tripod mount.Also, check out my project videos here! ...https://www.youtube.com/channel/UCJw_hr8h6O-QG6e49CBQ78w

Adapter for the raspberry pi arducam. Base has a hole that will need to be tapped 1/4-20 for a tripod mount.Also, check out my project videos here! ...https://www.youtube.com/channel/UCJw_hr8h6O-QG6e49CBQ78w

This bracket works with M3 screws and i have it mounted with this y-axis motor mount (https://www.printables.com/model/64402-raspberry-pi-camera-mount-for-mk3s). ...For those wondering that mount works on a mk2.5s, just gotta tighten the mounting screw...

I wanted a simple but sturdy way to mount my Raspberry Pi camera module (Arducam B0033) to a tripod via a standard tripod screw (1/4-20). The vertical variation rotates the base to a 90 degree position, which is handier for mounting to a tripod...

Purpose: - Still trying to work out where I want to mount a Pi Camera so purchased the ArduCAM CSI to HDMI boards, these little cases for both sender and receiver just snap together with no fittings required. ...Shouldn't be hard to graft on your own...

Purpose: - Still trying to work out where I want to mount a Pi Camera so purchased the ArduCAM CSI to HDMI boards, these little cases for both sender and receiver just snap together with no fittings required. ...Shouldn't be hard to graft on your own...

This allows the use of a Arducam or other general raspberry pi camera to be mounted in the center to record print progress through Octoprint or similar software. ... https://www.thingiverse.com/thing:1460181 ^ this is the tripod I used to make a...

This design is optimized to work seamlessly with boards that feature mounts for larger lenses, such as the Arducam 5 Megapixels 1080p OV5647 Camera Module with CS Mount Lens that I currently use. The board must measure less than 36mm and have...

Some time ago, I bought this UC-261, Rev.D camera from Amazon. After searching around on Thingiverse, I could not find a model that fit this model of camera. The Things I did find, were close but too small or the alignments were off. So I...

I revamped ClintonRH's initial concept by stripping away the GoPro-style holder and developed several alternative mounting solutions.

... camera. In my setup I've run the ribbon cable underneath the glass panel to a Raspberry Pi mounted to the side of the printer - but let your imagination run wild. ...Probably best to print out of PETG so it can withstand the temps inside the case.

I cobbled this together in TinkerCAD because it is a PAIN in the butt to find a camera mount for this specific board (the 36x36 board with the screws on each corner...) so! I made this! I jacked the mount point from one of the camera arms, removed it...

This is only the file for the camera holder.Be sure to download the mount file from my remix source at https://www.printables.com/model/725402-ender-3-v3-se-camera-mount/files.Then be sure to read the sources source model info,...

I cobbled this together in TinkerCAD because it is a PAIN in the butt to find a camera mount for this specific board (the 36x36 board with the screws on each corner...) so! I made this! I jacked the mount point from one of the camera arms, removed it...

<p>I cobbled this together in TinkerCAD because it is a PAIN in the butt to find a camera mount for this specific board (the 36x36 board with the screws on each corner...) so! I made this! I jacked the mount point from one of the camera arms, removed...

A simple holder / stand for a Arducam (UC-350). You can adjust the vertical direction using some M2,5 bolts (tilt the holder either up or down). For these holes no thread recut needed (for me). Yo can also mount this on a tripod (1/4 inch).

5MP OV5647 Camera Board /w M12x0.5 mount LS-40180 Fisheye Lens for Raspberry PiQuick CAD makeup of the ArduCam with lens

1.5 inch Telescope lens (1.2 inch diameter) mounting system for raspberry pi mounted cameras. File CamBody_ModuleV1 was designed specifically for arducam module v1. ... The three pieces can be tightly screwed together using 2 16mm M3 screws.

Remixed from https://www.thingiverse.com/thing:4713656 Modified the camera case to fit an arducam. ... Used M3x20 for the joints

A simple case for the Arducam UC-733 board.The Fusion 360 source file is included to make remixes easier.Hardware RequiredThis was designed around some basic hardware from McMaster Carr but their mesaurements are pretty standard and this case should...

A simple case for the Arducam UC-733 board.The Fusion 360 source file is included to make remixes easier.Hardware RequiredThis was designed around some basic hardware from McMaster Carr but their mesaurements are pretty standard and this case should...

This is a cam body block on Fusion 360 aiming you to use on case/support development

USB Camera Adaptor: https://www.arducam.com/product/arducam-uvc-camera-adapter-board-for-12mp-imx477-raspberry-pi-hq-camera/ Raspberry Pi HQ Camera:...

This multi-camera adapter board is designed for Raspberry pi ZERO and lets you connect two 5MP, 8MP,12MP cameras to Pi Zero.

This multi-camera adapter board is designed for Raspberry pi ZERO and lets you connect two 5MP, 8MP,12MP cameras to Pi Zero.

Rough prototype remix of two existing projects:https://www.prusaprinters.org/prints/45962-prusa-mini-mini-raspberry-pi-camera-module-v21-8mphttps://www.thingiverse.com/thing:3402755Parts:The Arducam night vision pi camera on Amazon (non-referral...

This is the same as the original, with the addition of an end to the IR-CUT Arducam 12mp high quality camera. You might need to sand the ball nut a bit, the fit is very tight. ... Here is the original for all other parts:...

This Arducam IMX219 fisheye lens camera module is designed mainly for Raspberry Pi V2 camera board and Nvidia Jetson Nano, replacing the default standard IMX219 camera module to get a much wide field of view. It can be used for drones, robots, action...