arcane 3d models

What fun! To build an adapter to your requirements, install Blender v3.80 (or later) and open the T2M42atapter_pre_assembly.blend file. Select menu View | Front (or press number [1] key on the keypad) to view the model from the front against the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 30 printer_tolerance = 0.35...

I created this VW Passat B8 phone tray because my iPhone 8 with cover didn't fit into the standard one. Rotating the USB port by 90° it has space for phones with a length of up to about 15 cm which is about 11mm more than the standard tray offers....

Sincethis design is compatible with a whole variety of lampshades, be aware that somelampshades will have to be scaled down or up to fit the base's default settings. Base- Layer height: up to 0.3mm is fine, there's little detail on the Z-axis-...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_radius = 6 custom_top_port_corner_radius = 5 custom_back_extra_port_y_position = 30 pattern_line_thickness = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

And get your supports in order first, the models need a relatively precise and flat supported surfaces. <font size="3">The modification uses many parts from the original setup, but the PTFE tube must be cut, making this a non-reversable mod...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.8. Can...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

I have left the original design files as well to preserve version control.&nbsp;Design File Included: .f3d, .ipt, step, .skp, and .obj files.&nbsp;Follow The Makers Workbench...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

They can easily be swapped around.PrintingMain HandleIn general you should use the flattest side of the model on the print bed. Your settings shouldn't be adjusted too much, the standard high quality settings of your printer (or whatever tuning works...

In the fanduct file they are included in the model. You will need: - x2 radial fans 5015 of 12 V. - x2 M3 screws of 25 mm. (To hold the fans above). - x2 washers for the M3 screws. - x2 M3 screws of 20 mm. (To hold the fans below). - x4 M3...

Modified the vent slots on the right side so they are less likely to cause problems during print. I really liked the compact ATX benchtop PS by gdoniu93 and started out simply to recreate the model in Fusion360. Somewhere along the way (as it often...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

The reason for the former changes is the way I modeled the original was a PITA to modify so some things had to get completely redone (and I left out the less important details to save time). The reason the STL's are so large is simple; I upped the...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

This model is for a “streetlight-style” wired garden/pathway light. Brighten up your garden path with lights, without spending a fortune on MoonRays or similar products where a single lamp can cost up to $20! In bulk I can make these for about $3-5 a...

Post-Printing // model: Prusa i3 MK3 Y Chassis Bearing Straps // This replaces the zip ties that tend to stretch and can reduce accuracy over time. Optionally, also replace the entire strap and bearing with a 1-piece printed version that has been...

Make the adjustments, render the desired  STLs and print it! The models are in the position, they should be printed. No support is needed. ...I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this...

&nbsp;The SFX version backplate does not fit the build plate of a Prusa Mk3, so this project is temporarily on the pre-prototyping stage.For the FlexATX version, click this link.&nbsp;The enclosed design includes two types of motherboard trays of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

This is the first 3-D model I have built from scratch and I was looking to get it done quickly. So, I kept it simple but did note that it wouldn't take much to add a few more amenities that would suit personal needs or desires. The router fits...

I have the model assembled if anyone is interested; just can't upload a .step file (check the comments for it now). Keep in mind that you may need a shim (flat washer) to fix any misalignment issues with the Creality Heatsink. I've used this...

Cheers. Print Settings Printer: D-Bot Rafts: No Supports: No Infill: 20% Rectlinear Filament: DASFILAMENT PETG Trans Blue / Trans Green Notes: You need: a heatbed because of the big surface of the model A coolerfan for the threads Category:...

I've updated the model with the Orbiter Ver. 1.5 as I purchased another one (I don't want to take the one I'm using on my Bear off as it works soooo good). I've also updated the filament sensor to use the Prusa MK3+ sensor as I have two of them. I've...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

For other sizes of tube or different grid arrangements, you can use the Thingiverse Customizer to remix your own version (the recommended way, so others can benefit from your work) or download the model and use the OpenSCAD Customizer (available in...

Description: https://youtu.be/G9-N-nIqc4g Assembly: https://youtu.be/2hdSGDdjpeQ Torque Capabilities Please note that I designed this CVT for a demonstration model, it's not intended to be used as an actual transmission. How This Works - Watch the...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with FDM...