arcade mod 3d models

I came up with this carriage for my EMT8 (modded A8), and needed a cooling solution for both the hot end and the parts fan. Initially, I tried several designs and all had their pros and cons. I took the best from each of the ones I liked and rolled...

... Credits to Long and WingZero for base toolhead and ducts which I have modified. https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/Long/Mantis_Dual_5015 https://github.com/mandryd/MantisUsermods/tree/main/Usermods/Wingzero

If you build this, as long as you incorporate my mods, the model looks great. If you go it on your own with the kit as it is... well... all I can say is good luck :) For best appearance, print at 0.1mm layer height in a shiny, metallic silver...

We have made several mods to come up with this re-design. The first thing you will find is that we have created our own headband. These will come in two sizes. One is for youth and will squeeze a little tighter to the head to give it more grip on...

This is a redesign of those designs, taking what I felt were the best parts along with a couple of mods by me. The Slide Shelf Ledge and Circular Mount provide stability, printability, and facilitate the blob! The Slide Shelf and Teflon Tape allow...

... the plate frame, now put on the top the plate and then screw to the fan top. The thin frame is to aid installation of two color plate and hide the color on the side.Connect the fans to the gpuFit the gpu on your caseI hope you enjoy with this mod :)

 I tested alternate screens on my Bear mod which does not have a heat sink on the RPi.  I designed alternate “aero inlet” and “simple bezel” and recorded the RPi temps during a print.  The original screen had the highest temp at 35.9...

Perfect for the ultra tiny Pavo Pico, the NewBeeDrone AcroBee75, or your Diatone Ripper pan camera mount! Just like my O3 Mod design, but I designed this to bracket-around the camera to hold it in place. The design puts as much material in front of...

This mod adds a 1mm diameter and 10mm long hole to support a 1x10mm metal shaft, enhancing stability in this region. The modified arm is available as a separate STL file for those who want to upgrade. For individuals without access to hard 1mm pins,...

Klingelknopf):...

I decided to try importing it into Tinkercad and possibly moving the filament guide to the right 3mm among other mods I did so it would fit on a 5:1 geared stepper. After about six or seven prototypes, I think I have it. I've been using the new...

... rings to make sure they are securely stuck on.</p> <p>That’s it! The print plate should go on and come off easily and there will be no shifting during printing. More mods for the Cube 3 can be found here: http://3dcreatorhub.com/viewforum.php?f=6

The default version has the BLTouch centered in the circle since that fit on my Hydra fan mod (highly recommended) ### Printing notes Support should not be needed on the cover-versions, while the model without cover needs a support in the middle for...

You can mod this as you wish yourself, add more holes, make lines, new art on it? It fits the Ivo perfectly. If you want a simple whole cover, use the Ivo1sidev2Modable.stl for a default nothing fancy cover. Has charging gap. *Emotional...

These parts are designed to work in conjunction with select Nerf blaster parts to turn a cheap water blaster into a functioning, half-length dart shooting, Nerf blaster. The Nerf parts required to complete this mod are as follows: Nerf Longshot...

I have a number of old Taulman spools with only a 19mm hole, so they don't fit either the stock tube or any of the other mods to fit the stock bracket. Like so many others, I found that the friction on that stock tube introduced quite a lot of...

My mods are: 1) Took the source .stl files and split the body into top and bottom. 2) Hacked in an access door into the bottom with plenty of room for a small breadboard, 3) made the ring thingy a bit taller so as better to control the sharp edges of...

5.) Slide Clip over the fan and duct 6.) Use 3x M3x25mm bolts to secure clip and fan to the inclined adapter 7.) Install 2x M3x8 bolts through slots in clip into the nuts installed in Step 3 8.) If installing BLtouch, bolt BLtouch to your bracket,...

I remixed this from 3 different models (thingiverse's post a remix option is not working for me, so instead of the links being on the bottom left of the page, you can find them right below): - I liked the mushroom cap design of the clip for the...

Just believe me, I have printed a lot of mods and most of them are good looking but add almost nothing to the actual printer's characteristics. That is not true for the dampers! You will experience a shocking difference in quietness and a good...

I made no Changes or Mods on those. <h1>Components Used in HiFi:</h1> 1. Raspberry Pi 3B as the main “brain” running Volumio (https://volumio.org/ ) 2. Official Raspberry Pi 7” Screen 3. IQAudio DigiAmp+ Hat as DAC and Amp. Generic 12V 10A...

But I did have to replace the main power leads and mod the heatbed connector. This needs to be done carefully as they are quite high current on this printer. The base part simply sticks with hot melt glue to the acrylic base. Then the MKS base...

Other mods have you print a spacer to hold the v6, but I think that's a pretty bad solution, sacrificing lots of rigidity and stability. This system eliminates that, but still leaves the spacing issue. I fixed this by simply lifting the heated bed up...

* **Affiliate links**: Not enough people are using my affiliate links, which means I don't have the budget to create new features or design mods. I hope you understand where I'm coming from. I'll continue to share my designs for free, but sometimes...

Original Post below: Do you have a modded out Wii U that has all the bells and whistles, but no good way to keep it all organized? Does your accessories for you Wii U include the likes of a GameCube 4-port controller adapter? One of those Rock Band...

I used AWG 20 silicon wire for the BMS connections.Zvones52o did the heavy lifting with his battery eliminator back piece for the GD-77  https://www.thingiverse.com/thing:2742838 , I just made some mods in Tinkercad to accommodate addition of two...

I remixed this from 3 different models: - I liked the mushroom cap design of the clip for the frankenquest mod for the original quest from foreverwinter https://www.thingiverse.com/thing:3892003 (who remixed it from this model:...

For leveling you can put a bench level across the flat part once assembled and up against the wall and then mark your holes.As always I have included the STEP file If you want to mod this (any real CAD package can import this - obviously it is metric...

Update 2: Added M7 hall gimbal protectors with extra large 15mm holes for the use of modded sticks such as the Grand Lotus (C on Banggood). Update 3: Major update! Added M7 hall fittings for 12mm sticks such as the Lotus (P on Banggood) We also...

... can be used.</p><p>After the glue is dry, screw on the existing lid of the Drybox, fit the locking knob, screw in the desiccant container and fit the filament outlet seal. I use the ingenious outlet from Xuis with PTFE tube connection.&nbsp;