araign xc3 xa9e 3d models

17 3d models found related to araign xc3 xa9e.
EVGA XC3 RTX 3090 EK VECTOR WATERBLOCK
EVGA XC3 RTX 3090 EK VECTOR WATERBLOCK
grabcad

EVGA XC3 3090 Graphics Card with an EK Vector waterblock on it. ...Modelled in AutoCAD and exported to IGES

Nvidia EVGA XC3 3070 3080 3090 Trim
Nvidia EVGA XC3 3070 3080 3090 Trim
thingiverse

I decided to take a shot at 3d modeling and printing trim cover for my evga xc3 3080 (but also works on 3070/3090 xc3) until evga has an official replacement. I had a little bit of a learning curve with fusion 360 but after watching a few videos I...

EVGA RTX 3060 Ti FTW3 / 3080 XC3 / 3090 XC3 shroud (3rd version)
EVGA RTX 3060 Ti FTW3 / 3080 XC3 / 3090 XC3 shroud (3rd version)
thingiverse

3rd version of my EVGA RTX 3060 Ti FTW3 / 3080 XC3 / 3090 XC3 shroud. ...This shourd might work for other models as well, as long as the fans are 120mm.

Xinje XC3 series PLC
Xinje XC3 series PLC
grabcad

PLC model design

EVGA RTX 3080/3090 XC3 custom Cooling Shroud
EVGA RTX 3080/3090 XC3 custom Cooling Shroud
thingiverse

I designed this shroud to fit the standard EVGA XC3 cooling block and fit 2x 120mm standard case fans for better cooling and noise performance. the shroud is designed to fit Noctua NF-S12A FLX Fans but could probably use any other 120mm fans. The...

EVGA shroud for 3060 Ti FTW3 / 3070/3080/3090 XC3
EVGA shroud for 3060 Ti FTW3 / 3070/3080/3090 XC3
thingiverse

Advanced decoration of my EVGA shroud.

EVGA RTX 3080/3090 XC3 custom Cooling Shroud (2 parts)
EVGA RTX 3080/3090 XC3 custom Cooling Shroud (2 parts)
thingiverse

I remixed the design since the Ender 3 has a smaller bed and I wanted to print with the fan side facing down. Split down the center and each piece fits a 120mm fan and a gap in between to run the fan cables. ... Photo with fans installed:...

ARAIGNED
ARAIGNED
cults3d

Found on the web is this original design link: http://www.thingiverse.com/thing:3185185. This is a disturbing wall decoration, ideally suited for printing in black. ...The dimensions are as follows: 50mm x 58mm x 5mm.

GTX 3070 Support
GTX 3070 Support
thingiverse

Needed a GPU support for my EVGA GTX 3070 XC3. ...(90mm)

Keves Power Frame Disc - Xenoblade Chronicles 3
Keves Power Frame Disc - Xenoblade Chronicles 3
thingiverse

Rough draft of the Kevesi Power Frame disc seen on many costumes in XC3! ...This one is theoretically scaled to the size seen on Eunie and Riku's belt, but could be shrunk down to fit the smaller ones seen elsewhere.

EVGA RTX 3070/80/90 FTW3 Accent Cover
EVGA RTX 3070/80/90 FTW3 Accent Cover
thingiverse

... accent piece. Tested on FTW3 only, because of the size difference it will not work with XC3 variants. Should work with RTX 3070 FTW3 as well. ... To install, line up and press down both ends of the cover, the centre piece should pop into place.

120mm fan GPU support
120mm fan GPU support
thingiverse

I installed this support bracket in the Cooler Master NR200P case on top of an Arctic P12 fan to support an EVGA RTX 3080 XC3. The GPU is more towards the back of the fans, therefore the fan/airflow clearance curve is off-center. The bracket plugs...

EVGA 3090/3080ti/3080 120mm backplate fan mount
EVGA 3090/3080ti/3080 120mm backplate fan mount
thingiverse

... GPU as it would be normally mounted. The full set includes a blank front section, but I have included a "FTW3" and "XC3" front section for both the right and left mount brackets total height added is just over 1.25in Tips are greatly appreciated!

EVGA RTX 3070/80/90 FTW3 Accent Cover
EVGA RTX 3070/80/90 FTW3 Accent Cover
prusaprinters

Tested on FTW3 only, because of the size difference it will not work with XC3 variants. Should work with RTX 3070 FTW3 as well. To install, line up and press down both ends of the cover, the centre piece should pop into place. Print Settings Printer...

EVGA RTX 3070/80/90 FTW3 Accent Cover
EVGA RTX 3070/80/90 FTW3 Accent Cover
prusaprinters

Tested on FTW3 only, because of the size difference it will not work with XC3 variants. Should work with RTX 3070 FTW3 as well. To install, line up and press down both ends of the cover, the centre piece should pop into place. Print Settings Printer...

EVGA RTX 3080TI FTW custom fan mount
EVGA RTX 3080TI FTW custom fan mount
thingiverse

... a little bigger, and centered better. Note: It might work for all the EVGA RTX 30 series FTW. Will probably not work for XC3 series though. ... Guide can be found at: https://forums.evga.com/EVGA-RTX-3080-Ti-FTW-custom-fans-guide-m3502802.aspx

Dove-tailed press fit LM8UU X-carriage
Dove-tailed press fit LM8UU X-carriage
thingiverse

An updated version (XC3.6) is available with additional material to prevent warping and added mounting points for quick fit extruder hardware. To print the necessary parts, create four bearing holders, one carriage, and two belt clamps, ensuring your...