arachne 3d models

PLA is less suitable as the fan shroud is too close to the heater block.Slicer settings:The model is oriented in the intended printing orientation0.4 mm nozzle (0.6 mm nozzle can be used when using the Arachne slicer engine in Cura 5.0 or higher).4...

When you get an error, close the Parameters dialog, undo and try again in smaller increments.  Print InstructionsThe compliant hinge will work best with PETG, but ABS, ASA or even PLA will work as well but may break if open/close-cycled too...

For example, a magnetic plate for a bed is also suitable.This project was design to be printed using 0.4mm nozzle at 0.2mm layer height with Arachne wall generator. All models printing without supports.Attention! Your bed or print plate on your...

Simple OD gauge on the side, length in the slot down the front, and reference printed-in threads in the back.Thanks to Sneaks for his original design that I remixed back in the day that also served as the direct inspiration for this!Printing...

 If you set the files up in your chosen slicer, then I suggest using the following settings:Arachne wall generator 15% gyroid infill.PLA for the bases and PETG for the LID, since it has an integrated spring. I used a textured PEI plate, but if you...

&nbsp;For this, I also recommend using the slightly longer tapered arms (crossbow_arm_short, crossbow_arm_short_mirrored) as well as the new “arachne” option in PrusaSlicer 2.5.0+. &nbsp;</p><p>Finally included is a front piece that allows the use of...

Finally, if your printer has any noticeable elephant's foot, then forget about printing this. SettingsDesigned for a 0.4mm nozzle0.16mm or 0.2mm layer height3 walls≥5 top/bottom layers20% infill (but more feels better)Slice with Arachne if...

You can find the tray here: https://www.printables.com/model/361287-gridfinity-tray-for-ikea-samlaRecommended print settingsFor my bins I use the following settings:0.2 mm layer hight3 walls10% infill (rectilinear)Arachne wall generatorParametric...

For this model, I printed this model with the perimeter generation set to 'arachne'. Some small parts are affected by the perimeter generation parameter and this worked best for me. 1 - Only shirt.stl requires some supports, only under the elbow. An...

These ends allow for perfect parallelism adjustment tailored to your carriage, however it does require significant patience during assembly.BOM:4x M3x6 cup-point grub screws4x M3x3 cup-point grub screwsThin HDPE/Kapton/paper strips for additional...

Now with the Gen2's rail design you can quickly swap the storage units between work areas.Download the GEN2 Interactive Catalog PDFUPDATES10/11/2023Tool insert holders designed to fit some of the most common 3D printer tools and accessoriesGEN2 Tool...

          As noted, these have not been tested yet, so if you make them, please provide feedback.I recommend printing these using PETG, with 100% infill and arachne wall generator for maximum strength.  Other filaments can be used, I have used PETG...

You also might want to re-slice the pieces with the new Arachne slicer and maybe get a better result.To play the base game, you need six each of Drone, Pawn, and Queen. A four-player game, played on a normal chess/checker board, would have twice as...

One set of settings is Arachne for general use, the other set is newer and is optimized on curved overhangs, which are quite challenging, it may also work well for general use. For details and to optimize for your printer, read...

This is very important.If you scale the model up to 130%:Line width / Extrusion width: 0.8mmBottom thickness / Bottom layers: 1.5mm (that's 5 layers at 0.3mm layer height… be sure to check the preview to make sure that all solid bottom layers are...

IMPORTANT: be sure to use the Arachne Perimeter Generator if the slicer allows. Otherwise, set 0.38mm external perimeters width or some perimeters will not be printed correctly. NO SUPPORTS IS NEEDED!The lever is the most critical part and it should...

Now with the Gen2's rail design you can quickly swap the storage units between work areas&nbsp;&nbsp;&nbsp;Download the GEN2 Interactive Catalog PDFFeatures:• Gen2 rails allowing quick and easier swap-ability and combinations of many Gen2 Storage...

Now with the Gen2's rail design you can quickly swap the storage units between work areas.Download the GEN2 Interactive Catalog PDFFeatures:• Gen2 rails allowing quick and easier swap-ability and combinations of many Gen2 Storage System designs.•...

&nbsp;I am not responsible for the parts not going together if you stray from the bill of materials listed.&nbsp;Print Requirements:No supports!Parts are already oriented properly for printing, do not flip them (rotation is fine).Designed with 0.4mm...

Now with the Gen2's rail design you can quickly swap the storage units between work areas.Download the GEN2 Interactive Catalog PDFFeatures:• Gen2 rails allowing quick and easier swap-ability and combinations of many Gen2 Storage System designs.•...

Now with the Gen2's rail design you can quickly swap the storage units between work areas.Download the GEN2 Interactive Catalog PDFFeatures:• Gen2 rails allowing quick and easier swap-ability and combinations of many Gen2 Storage System designs.•...

... set Type to normal(auto), Style to Default, Threshold angle to 35, and Remove small overhangs to checked. On build plate only doesn't matter. Uncheck Reduce infill retraction in the Others tab. Set Wall generator to Arachne in the Quality tab.

All files are sliced in Prusa Slicer (V 2.5 with Arachne) for a Prusa i3 Mk3s (0.4 Nozzle) and for PLA.Base Ring:PartInstructionsQTYTop RingLayer-Height: 0.2 mmInfill: 15%Supports: NoColor: Base colorIf you are using a Prusa i3:You can fit both parts...

I would strongly recommend ABS or ASA filament unless you want to experiment with settings and tolerances yourself.Print one copy of each of these files:Full-frame - 5mm baseline - Body set.stlFull-frame - 5mm baseline - Camera connectors - 2x...

The chanter reed body needs to be printed with perimeter generator set to classic, not Arachne.Chanter reed tongueDrone reed tonguePLAReed tongues must be printed in PLA or they will be the wrong weight/stiffness. I suggest you avoid PLA+ or any kind...