ar 900 wing 3d models

A nose piece to fit an Osmo Action camera in the AR Wing Pro, either flat or at a 7deg downward angle as per the remixed design. Designed to fit over the stock plywood plate and use one of the included straps to secure the camera in place even more...

2205 Motor mount for the Ar Wing Mini, install on the original balsa mount with the original screws. I made this as the other mounts available was quite difficult to attach due to the screws being very close to the motor bell housing. ... This mount has...

Lens wiper for Sonicmodell Ar Wing Pro or other wings. Servo link for 0.8mm rod. First, bend the rod for the wiper. Make it a bit curvy. Glue some sponge stripe on it. Then push the rod through the wing. Find a suitable place for servo, cut...

... screws. A slot needs to be cut into the fuselage on the AR Wing Pro to allow the latch to positively engage. The alignment is such that when the hatch is closed the finger hold on the top will align longitudinally with the aircraft. ...

This is a FC & Battery holder for Sonicmodell AR Wing Mini. It can hold an FC with 30.5x30.5mm mounting holes (I've used Kakute F7 HDV) and 4 li-ion 18650 cells. FC is mounted on the back of this compartment (not seen on the render). The battery...

This model adapts the standard HS1177 camera mount to a micro camera, making it ideal for use with the AR Wing. The original design used a small lens, but this revised version accommodates the large lenses found on some cameras. I hope you enjoy...

I've redesigned a squid plate for the AR Wing Pro based on the provided teflon stickers. This plate is used on far end of the belly to protect my 3536 sized motor which is wider than the standard Sunnysky 2216. But it can be used to replace your...

AR Wing Pro weight pod to help get perfect CG with different battery setups. The pod can be filled with lead, ball bearings or any other suitable material to get the weight balance you need. The pod will sit in place without any screws or can...

TBS Crossfire immortal T antenna hinged mast mount for Sonicmodell Ar Wing Pro. This requires Extended (120mm) or Extra Extended (220mm) antennas to guide inside the box or fuselage. **Update 2020-12-15:** Added STEP file for remixing :) You...

After several malfunctions of my AR Wing, I had to redesign a new tail and reinforce the motormount. I decided to remove 14mm of EPP from the old tail and glue in the printed one instead. I also added a standard version, which allows you to cover...

Simple cover for fitting a Strix LED strobe light into the GPS bay on the Sonicmodell AR Wing Pro. ...<a href="https://www.readymaderc.com/products/details/strix-strobes-red">https://www.readymaderc.com/products/details/strix-strobes-red</a></p> <h3>...

This mount slides into the camera cage on the AR wing, securing via velcro to the rear platform, with velcro straps threading through the middle and a self-tapping central screw at the base. To accommodate the mount, you will need to remove a...

AR Wing matek f411 wing + ublox m8n mount Use some m3 standoffs for the gps mount (I used 20mm standoffs), then glue the base to the foam. You could use the m2 screws that come with the matek fc to fasten it, I used some longer ones. ...The GPS module...

Mount the AR Wing's Matek F411 wing to a U-Blox M8N mount. Secure the base of the mount to the foam using glue. Some M3 standoffs are necessary for the GPS mount, so use 20mm standoffs as an example. ...Then fasten the Matek FC to the base using longer...

Mini Wing Extension Kit for Compact Aircraft Wings, 24 Inch (600mm) Length

I recently purchased an Ar Wing Pro and love it but it requires more weight at the front to keep the CG if you are not using a heavy HD camera at the front like a Hero. I decided to merge this nose https://www.thingiverse.com/thing:4728940 and this...

cable organizers I designed for use in my fpv wing

I like this little wing, but motor must be bigger :)

The Winglets on the AR Wing Pro are mounted using wooden parts. This is a reasonably accurate reconstruction. The holes are in exactly the right place and the part fits very precisely. Unfortunately I forgot to take a picture before i glued it in. ... ...

The Winglets on the AR Wing Pro are mounted using wooden parts. This is a reasonably accurate reconstruction. The holes are in exactly the right place and the part fits very precisely. Unfortunately I forgot to take a picture before i glued it in.

Extended nacelle for Mini AR Wing with provision for an Emax 1606 motor. Moving the propeller further back really reduces noise significantly. I've been able to get about 15 minutes of almost silent flight (75% throttle and under) using the Emax...

Neat cover with airflow vents if you want to use this hatch without DJI Air Unit Watch a review of my AR Pro Mods here: https://www.youtube.com/watch?v=U8NLCYz1H8Q

Hide all your cables underneath this cover to give a neat look with full access to usb port Watch a review of my AR Pro Mods here: https://www.youtube.com/watch?v=U8NLCYz1H8Q

Just a cap that lets you fill you forward foam nose with BB weights so get the perfect CG on the Wing Video- https://youtu.be/YLiWtnxZNOs

Printed in PLA and then wet and dry sanded for max airflow, Bond 2 x M3 standoffs and fasten with thumbscrews from inside of front fuselage bay. ... Watch a review of my AR Pro Mods here: https://www.youtube.com/watch?v=U8NLCYz1H8Q

... used a plastic stand off embedded and glued into the foam and plastic M3 thumscrew to hold in place. Wear plates to protect the foam are bonded with superglue. Watch a review of my AR Pro Mods here: https://www.youtube.com/watch?v=U8NLCYz1H8Q

... it seamlessly. The spacer measures precisely 15mm in thickness and boasts an identical design to the wooden plate found inside the wing structure itself. ...To ensure optimal performance, using 8mm brim is highly recommended throughout the process.

Vertical mount for MATEK F441-WING and MATEK F722-WPX flight controllers. Mount will be held in place firmly with the carbon rod. So no need for any glue or screws. Center of gravity is also spot on (when used with 2 x CNHL 1500mAh LIPOs). ...

... tape for easy installation. There are pre-drilled counter-sunk screw points on each board if you prefer to use screws for mounting to the wing. ...Alternatively, a bead of hot glue or additional double-sided tape can also secure the boards in place.

Crossfire Nano Mount and Cover that holds Immortal T antenna in place Watch a review of my AR Pro Mods here: https://www.youtube.com/watch?v=U8NLCYz1H8Q