aquila favonia best for 3d models

This is a display mount to orient the display of the Voxelab Aquila in a portrait or vertical manner. This display holder raises the display by about 11 degrees from the aluminum rail. The latest version has fits perfectly with no wiggle. When I...

When using the Red Lizard Q1 on the Aquila S2 Pro, the source CR Touch bracket is too short. I remixed one I found and added 9mm in thickness to it. I have not operationally tested it yet, but I did create a mesh using it with no problem. This will...

After I dug around trying various direct drive extruders for my Voxelab Aquila, many were horrible to print, and none of them quite had everything I wanted, so I designed this one. Design goals: 1. Be easy to print, with minimal supports and...

... No promises, no guarantees. I can only claim accuracy to the measurements taken from a different Aquila Satsana. 12/10/2021 Relocated ABL mount per request. Again, this is untested as I do not use or have ABL. ...Comments appreciated.

... flawlessly. No promises, no guarantees. I can only claim accuracy to the measurements taken from a different Aquila Satsana. 12/10/2021 Relocated ABL mount per request. Again, this is untested as I do not use or have ABL. ...Comments appreciated.

So you want to use a BL or CR Touch with your Aquila H32 huh? Current firmware is locked and buggy. 1/21/2022 You will need to grind down some of the (temperature) leads on the back of your replacement Creality board with a file or Dremel. After...

Cooling Mods There are a lot of these out there, but if you haven't picked one out, check out the ones I designed and currently use: Ender 3\Aquila PSU mod: https://www.thingiverse.com/thing:4972200 Ender 3 Mainboard mod:...

**Cooling Mods** There are a lot of these out there, but if you haven't picked one out, check out the ones I designed and currently use: Ender 3\Aquila PSU mod: https://www.thingiverse.com/thing:4972200 Ender 3 Mainboard mod:...

In addition, on the left carriage of the X-axis, Aquila has a technological hole for an incomprehensible purpose. And as part of the spare screws attached to the printer, there is an M4x8 screw. Details need to be printed, as in the screenshot from...

CRTouch mount for the Push/Pull fan shroud by [mjwanetka](https://www.thingiverse.com/mjwanetka)

The original file had no clearance for the fan vents. ...I cut a slice off to add about 1mm clearance.

... the rubber pad holds it more securely. The additional height provides room for taller mainboard covers like the one I'll be uploading soon. ... This version adds 35mm of additional lift and uses M4x20mm socket head cap screws and M4 T slot nuts.

!!! ...It doesn't fit to BTT or Fysetc mini 12864 displays. Only for MKS MINI 12864 v3 It has no SD card slot because i use klipper software

Created as a part of Titanator RBS (Remote Blower System) Original Titanator V3 - https://www.thingiverse.com/thing:5542713 RBS for Titanator V3 - https://www.thingiverse.com/thing:5742869 Designed to be printed with ABS, PA or infilled ABS/PA/PP...

i forgot the rear screw, should work perfectly anyway, currently printing for myself, includes support for cables at the top and the bl touch, u can do ironing if u want, it looks much better.v2, after printing, i wasn't able to put the cables, so i...

This is a remix of this shroud: https://www.thingiverse.com/thing:4877288 The air ducts were too close to the bed. ... So I moved the air ducts up 2.5mm for more clearance.

E3D Minimalist for V6 & Volcano on Creality CR10/S Ender 3/Pro and clones by mediaman's : https://www.thingiverse.com/thing:3393889 I put the Voxelab logo on the bracket. ...That's all I've done.

Made the holes bigger so it can be used with a Hotend Fitting so the tubing can go right up to the stepper head. ...This is prefect for printing with TPU.

BLTouch mount for the Push/Pull fan shroud by [mjwanetka](https://www.thingiverse.com/mjwanetka) Remixed from another fan shroud. ...I do not have a BLTouch so I cannot guarantee fitment.

Created as a part of Titanate RBS (Remote Blower System) Original Titanate V3 - https://www.thingiverse.com/thing:5542713 RBS for Titanator V3 - https://www.thingiverse.com/thing:5742869 Designed to be printed with ABS, PA or infilled ABS/PA/PP...

+ Fits any 3D printer, that uses ender-3 ot similar hotend + Printhead can be removed for service by unscrewing only 2 screws + No print volume losses + Easy to print - no supports needed + Improved air flow for both hotend and model cooling ### BOM...

If you choose to use a different 12v fan for the heatsink then adjust the resistors to match the value as the fan. Fan resistance = 12/Fan_current. Use two 1W resistors in series to add up to the approximate value. E.g if the fan current is 90mA,...

... cleaned up the Satsana model a lot, removing a lot of surface artifacts. The design only gives marginal improvement to overhangs but print surface quality is better on all sides.It's a lot quieter too which is the biggest reason for this upgrade..

... ...Just another camera holder. I tested it only with a generic camera for 6 GBP. Not sure about the original one. You need to attach it with the belt knob on the front. You can use a little washer if you like. ...Some double tape could be required.

... printable orientation. ... Still needs supports but normal auto supports in Cura worked fine. I think this is what the original author intended but it was easier for me to rotate it in Tinkercad than in my slicer because it was not a simple 45 or 90.

A height increased version of the original for proper alignment with a dual extruder, you know, the typical red ones that are all over amz and eby. This is 12mm higher than original. ...If the bearing/wheel is needed grab it from the original thing but...

... conical mounds that have the holes through them that mount on the back of the carriage plate is face down. ...You want your layer lines for the stepper mount to be going vertically when the part is righted to prevent breaking as it is decently thin.

... are meant to be used with two 300mm 2040 extrusions to tilt your printer 30 degrees. ...It should work with most ender 3 style printers. Hardware 12 x M5x10 12 x M5 t-nuts/hammerhead nuts I added fusion files for anyone who wants to make changes.

Remix of [c2nsored's](https://www.thingiverse.com/thing:4821959) Satsana remix for V6 clone hotend. Took [TheSubaruJunkie's](https://www.thingiverse.com/thing:4817245) Satsana remix and cut off the BLTouch mount. Then just combined the two. ...

... created, but when I printed mine in regular PLA it flexed diagonally around the axis between the screws when clicking the display-button. ... So I made a new version with an additional brace, and the new version is much more steady for me now.