aquarium hose fittings 3d models
507153 3d models found related to aquarium hose fittings.
thingiverse
Customized version of https://www.thingiverse.com/thing:2139028 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2139028
prusaprinters
<p>Reinforced host clip with slightly thicker wall.</p> <h3> Print Settings</h3> <p><strong>Printer:</strong></p> <p>Creality CR-6 SE</p> <p><p class="detail-setting rafts"><strong>Rafts: </strong> <div><p>No</p></div><strong>Supports:</strong></p>...
prusaprinters
M14x1.5 to 14 pipe adapter. The original adapter broke so I had to design one. ...Prints good with PETG.
thingiverse
Customized version of https://www.thingiverse.com/thing:2139028 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2139028
thingiverse
Customized version of https://www.thingiverse.com/thing:2139028 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2139028
thingiverse
Customized version of https://www.thingiverse.com/thing:2139028 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2139028
thingiverse
Customized version of https://www.thingiverse.com/thing:2139028 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2139028
thingiverse
Customized version of https://www.thingiverse.com/thing:2139028 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2139028
cults3d
Designed specifically for 6mm glass. ... Holds a dosing/ATO tube and wires
grabcad
Other options are a 3" male NPT connected to a male camlok, two sizes of male NPT hose barbs in straight and 90-degree forms, a close nipple in three sizes, a bushing for 2" and 1" NPT connections, a threaded 3" ANSI flange, and a 1" bulkhead...
thingiverse
... in total. One is a hose fitting that allows you to attach a 2.5-inch ID flexible hose to both a cabinet and a refrigerator. This part also has space for a Noctua 40MMX10MM fan. ... The other component is a straightforward 6mm ID hose fitting.
thingiverse
The outer diameter (OD) on both sides fits the Rockler hose/handle, and the inner diameter (ID) has differ tapers on each side to fit a variety of machines and other 4" fittings like the hood pictured. PETG recommended over PLA for strength and...
thingiverse
Aquarium water pump accessories for water change (hose guide and strainer foot valve) - 16/12mm
thingiverse
10 Gallon Petco Rim Aquarium ATO hose holder with zip tie holes
myminifactory
I built this because my original hose clip on my Dennerle Nano Cube wouldn't fit without raising the lid on my Tunze Osmolator nano. So, I created something that only needs a 5mm gap between the top and side glass. Just push the hose into the holder...
thingiverse
These are created because I needed them in plastic and all I could find locally was brass. I printed them on 0,15 res 100% infill and concentric fill. If you use PLA and a glass bed, there is no need for a raft. To make the thread go in you just...
thingiverse
I designed this because on my Dennerle Nano Cube, the original hose clip of my Tunze Osmolator nano wouldn't fit without lifting the lid, so I made a thing that only needs 5mm clearance between the top and side glass. Just press-fit the hose into the...
prusaprinters
I designed this because on my Dennerle Nano Cube the original hose clip of my Tunze Osmolator nano didn't fit without lifting the lid. So I made a thing which needs only 5mm clearance between the top and side glass. Just press fit the hose into the...