aperture science logos 3d models

I'm obsessed with the Imperial cover design, but it lacked a matching element - the Extruder knob and fan cover didn't quite fit in. ...So, I cleverly combined them into one seamless unit.

A tiny circular opening has been incorporated into the design to facilitate precise placement of the magnets in their ideal center position.

Customized Version of Thingiverse Thing Id: 813330 Created with Customizer - Run in Thingiverse Instructions Using the Following Options: - width = 67 - swidth = 6.1 - height = 9.5 - mashup_type = 1 - pattern_overlap = 0 -...

Seeing as I was new to CAD when I started designing this case it has turned into a nightmare to edit. Anything and everything breaks upon editing a single sketch or extrusion. So I have decided to make a new case from the ground up with better...

Instructions for the Spinning Book End Using these customizable settings: Spine Size: Adjusted to a standard thickness of 3 units Spine Rotation: Set to maintain perfect alignment at 0 degrees Corner Radius: Enhanced with an added smoothness factor...

Modeling by Solidworks. You need to print 12 copies of the blades and pins,the pins are in dia-3mm,so some rafts are needed to fix them on the platform.And because of the elephant leg,the pin maybe larger than the blades hole,you should fix it...

I have provided an indented and an extruding version, the indent one should be twisted 90 degrees so it is face down before you slice. ...And you might wanna put support blockers over some parts.

IMPROVED VERSION AVAILABLE HERE:\r\nhttps://www.thingiverse.com/thing:3864546\r\n\r\nWho needs a weighted companion cube?\r\nIt can store various items.\r\nThe lid fits snugly, but it worked for me.\r\nI examined the measurements and they seem...

This is a replica of the computer cases found in Portal, but designed for a Raspberry Pi, Asus Tinker Board or any other device with a similar board configuration. The case can accommodate up to three 30mm fans in the front and one 40mm fan on the...

I crafted this custom part from scratch for my Ender 3 extruder, carefully designing it to fit snugly on the 5mm shaft. The component measures 40mm wide, with a flat area width of 4.5mm and an opposing side width of 4.5mm as well. ...I created this...

Portal Case! ...Ultimate Accessory For Die-Hard Fans!\n\n \n \n Essential Details\nTreat it just like a standard case when printing!

Modeling by Solidworks. You need to print 12 copies of the blades and pins,the pins are in dia-3mm,so some rafts are needed to fix them on the platform.And because of the elephant leg,the pin maybe larger than the blades hole,you should fix it...

Added a small round "hole" so that it is easier to attach the magnets in the exact middle.

Seeing as I was new to CAD when I started designing this case it has turned into a nightmare to edit. Anything and everything breaks upon editing a single sketch or extrusion. So I have decided to make a new case from the ground up with better...

<p>Added a small round "hole" so that it is easier to attach the magnets in the exact middle.</p> Category: 3D Printer Accessories

A science logo I designed and printed for my workspace in the lab where I work. Underneath the print is a caption reading ' ...Stay curious' inviting those who lift and examine the model to take a closer look. To make printing easier with minimal...

The logo from the Portal 2 Mod called "Aperture Tag"

... Version of Thing 1038261 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1038261 Instructions Using Following Options: -45 degree zRotation 10 times Larger zScale 50 Units Larger xTranslate wholeMessage = Science

For details on the specific options used, see below: Text style: 25 Font size: 8 Corner radius: 3 Line spacing: 2 Slit width: 4 Plate thickness: 3 Letter spacing: 1 Font: write/orbitron.dxf The customized message reads: Line 1: #1 Line 2: Science...

Aperture Tag Logo Shines Brightly as Players Join the Thrilling Gameplay of the Portal 2 Mod.

Aperture Labs Logo insert for : https://www.thingiverse.com/thing:4589744

The Aperture Science emblem takes center stage on this limited-edition coin, proudly displaying the iconic blue circle surrounded by bold lines and a sense of innovation.

Logos of some of my favs.

These are some conceptual logo designs.

Automaton logo piece Rewritten: A logo component featuring an automated machine

One more Aperture Laboratories Logo Print Settings Printer: Discovery 200 Rafts: Yes Supports: No Resolution: 0.15 mm Infill: 25% Notes: To get a perfect rendering, add a Z move of 0.1-0.2mm while retracting to prevent scratches on the outer surface....

Humans are accustomed to logos coming in a miniature format.

Re-creating logos for Suncoast Technical College's various programs

Using SolidWorks, Logitech and Microsoft have created their respective logos as representations of their brand identities.

Logos dessinés et découpés sur machine plasma.Sablage des tôles découpées.Mise en peinture en cabine.