aos 5 3d models

v2 of this design: https://www.thingiverse.com/thing:5615407 Durable design, holds itself steady on the arms. ...Designed for the new AOS5 v2 frame by Chris Rosser.

Chris Rossers AOS5 antenna mount and GPS BN-220 mount. Put GPS wires under the bottom and run the antenna through the hole. ... TPU - 100% infill S1 Pro 1.2mm retracement 215c / bed 60c

Simple Remix from original Mount to use the full height of Standoffs for a cleaner look.

I've re-mixed my insta360 go mount for the AOS5 frame. It works on both the V2 and Evo and likely other versions. ...Those are the only 2 I tested though.

GoPro Hero 9 10 11 Mounts for the standard AOS 32x32 Mount I personally print all my TPU Mounts with 100% infill but up to you what you do. For added strength, use a heatgun to slightly melt the outside layer of the print which gives it a glossy...

... the front. Light weigh design with many gaps to prevent heat build-up. You need: 4x M3 nut 4x M3 6mm for AOS5v2 frame or 3.5 mm + bottomplate mm screws for any other frame Fits well with this antenna mount: https://www.thingiverse.com/thing:5563243

Designed this after XT60 connector desoldered. ...I printed in PLA, seems to hold it pretty well

The file by kt4rj is for the arms with 3 holes, this is for the ones withe 4 motor holes. ...Done and with permission by Yamie - Thank you!

Complete the look with some TPU covers that press fit onto the camera mounts.

bando - more angle cine - less angle for cruising use hard tpu eg.: extrudr flex hard. ...(good results with treelike supports) fill 100% for crash resistant and no jello use additional zip tie in middle of base to make no jello v1

Use TPU that is not too soft if you want to avoid vibrations from the antenna flopping around. With Priline TPU 98A shore I got good result. Not affecting the PID tune at all. The hole for the antenna is tight, and its a bit hard to push the ufl...

Integrated arm guard with feet for a softer landing.

Very light weight arm guard that also prevents the screws on the motors scraping away when landing on concrete. ...Snap fit so don't interfere with motor screws

Vertical (standoff) : 3 mm Horizontal (antenna) : 4 mm reduziere size = 90% 2mm

Print in TPU and attach with M2 screws and captive nuts.

It holds under motor,that way you can tight you motor all the way the hole patron is 12x12 print in mirror to get the other side prints

<p>Integrated arm guard with feet for a softer landing.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p class="detail-setting printer"><strong>Printer: </strong> <div><p>Ender 3</p></div>...

print out of tpu

Ultralight and low profile DJI Action 2 camera mount for AOS 3.5,5,5.5 or other FPV quads width 30mm /32mm wide mount. The hols are 3mm and 31mm width. Recommend to use washer. No props in view. ... Follow me on Youtube: ...

iFlight AOS 3.5 O3 HD 4S Thumb and GoPro mount

... design from penguin2600, I added the minimortal part. ... Adds minimal weight. (About a 2 grams in TPU) AOS35 / AOS3.5 / AOS 35 / AOS 3.5 / Cicada :) I'm a noob in 3D printing and designing parts, and hopefully this will be helpful for some people :)

This mount for AOS 3.5 works with O3 antenna (or with any antenna with 4+ mm tube outer diameter i.e. rush cherry) and matek gps SAM-M8Q module. ... Antenna only version is available too.

Dummy reproduction of a russian subnuition AO-2.5 RT dropped by the airplanes as a cluster bomb.This reproduction is just for learning purpose. ...I hope for a small tip to support my creations :)Thank you so much

I loved to original design of the arm bumper for this design (https://www.thingiverse.com/thing:5392632) but they seemed pretty loose to me. So, I increased the heigth of the rim and added some cover material - now the feet slip right on and stay...

Merged two mounts into one for innitial print on new build.

Printed on Sovol SV01 using saint smart TPU and my tunning preset that you can find on the files section.

I don't like how Chris mounts his antenna. LOL. so this is my take for the back side. to get an expresslrs ep1 and sma antenna altogether in a stiff mounting. ... In the near future i might add in a gps

My beeper was originally secured with a zip tie, but I've created a holder to attach it using the two screws located at the front of the frame. ...It might add a bit more weight compared to the zip tie method, but it should result in less jarring and...