aos 5 3d models

3D printed accessories for AOS 5 and 5.5 V2 FPV quadcopter frames.More info:https://www.aos-rc.com/Designed to be printed in TPU for flexibility and protection.Minimum 2 perimeters/walls and 5/4 top/bottom layers, infill 20% up.These fit both AOS 5...

If you like it, consider tipping :-) Please also have a look at my other creations for the AOS 5.5 AOS 5.5 GoPro Mount: https://www.thingiverse.com/thing:5248649 AOS 5.5 Caddx Polar Antenna Mount: https://www.thingiverse.com/thing:5248655 AOS 5.5...

If you like it, consider tipping :-) Please also have a look at my other creations for the AOS 5.5 AOS 5.5 Crossfire Immortal T Mount: https://www.thingiverse.com/thing:5248645 AOS 5.5 GoPro Mount: https://www.thingiverse.com/thing:5248649 AOS 5.5...

Simple remix of the nice mount designed by Kozawa to allow attachment to AOS 5

A GoPro mount for an AOS 5 drone. ...32 mm mounting.

FPV Drone - GoPro Hero 4 Mount for the Chris Rosser AOS 5 series of frames.

Side mount for a BN220 GPS module for Cris Rosser's AOS 5.5 (and probably also for 5.5) V2. ... The position on the side avoids interferences between back-mounted antennas and GPS module.

On my AOS 5, I used the front/center XT60 passthrough to route the power lead. The issue is that it has no strain relief and I'm afraid of ripping the pads off if the battery ejects in a crash. This uses the rear GoPro mounting holes to attach to...

Gopro Hero 11 mini mount with 25 degrees. ... Made for the AOS 5. ... print with 15% infill and supports

Perfect for me and my AOS 5.5....The Angle of the Go Pro Hero 8 is 25 degrees....I choose this design because it is lightweight with moderate durabilty......This should be printed in TPU ...Send it I printed it on a Ender3 Pro,, however any printer...

This is a light weight TPU holder for the AOS 5.5 It snugly fits a Hero 8 but doesn't Provide that much protection so no bando smashing with this one :I Also included is the fusion 360 file if you want to Chane anything

O3 antenna holder for AOS 5 V2 I haven't tested the fit yet as I am still waiting for my O3 unit

Antenna mount for the O3 system on an aos 5 frame. ...I only have a resin printer so someone will have to let me know if this works in TPU as well.

Arm guard for AOS 5 v2 frame. Don't need to unscrew the motors and no untightened screws due to the TPU part. Just snap it on and you're good to go! Print in TPU, 2x the parts + 2x mirrored parts. ...No raft and support is needed.

- Hero 9 mount approx 21 degrees for AOS 5 - Centre shelf to run wiring beneath cap and receiver - rear antenna mount for bare coax antennas like the lollipop v3 and tbs triumph ufl antennas hero 9 mount and antenna were remix's but apologies cant...

This is a mount to attach the hdzero nano 90 camera to the aos 5 using the horisontal standoffs instead of the holes on the side. I kept having problems with the side mounting holes on the nano 90 being very shallow and not allowing good bite, so...

Selection of TPU accessories you might need for the AOS5 and AOS5.5 by Chris Rosser. The full sized gopro mounts are for the Hero 7, but I have included a solidworks file and an STL of the mounting base in case you want to use another CAD program...

TPU mount for the AMASS XT60E-M panel-mounted XT60 connector.

Supporto per antenna vtx, immortal-T e gps (HGLRC M80PRO GPS QMC5883 25mm x 25mm x 8.3mm)

aos5 O3+gps

AOS 3.5 side mount for receiver.

Landing feet for AOS 3.5 quadcopter

I know it will fit the AOS 5.5 V2, as well as the AOS 7. I printed in TPU, at 15% infill, and I turned it on it's top so the antenna mounts were flat against the build plate. Supports on build surface only. ...Should create an easy to remove plug...

Runcam Thumb mount for AOS 3.5 frame

AOS 3.5 immortal T and VTX antenna mounts

Here is my Caddx Walnut Mount for the AOS5.5 (will probably fit other AOS models , however that is for you to confirm) The bottom portion of the mount is extra Thiccc for improved durability during hardcore Freestyle Printed on Ender3 Pro Material:...

I know it will fit the AOS 5.5 V2, as well as the AOS 7. I printed in TPU, at 15% infill, and I turned it on it's top so the antenna mounts were flat against the build plate. Supports on build surface only. ...Should create an easy to remove plug...

AOS 3.5 Arm Guards you will need slightly longer motor screws

Arm Guards for the AOS 5/5.5 with motor protection. ... Printed from PETG.

Print in TPU with 30% gyroid infill. ...Fits AOS 5 and 5.5 V2 / O3 / EVO.