anytone at868uv 3d models

I remixed a model from here: https://www.printables.com/model/299155-anytone-878-versamount-2-adapter to make an adapter specifically for the Anytone BT-01 Bluetooth mic so you can put the belt clip through the adapter and then use a standard...

A custom design inspired by Rexfreund's Anytone 8x8 Holder. Modified to seamlessly integrate with a standard RAM mount system. The top section has been carefully angled at the back, allowing the beltclip to effortlessly slide and click into place...

Inspired by another stand I saw, I made this stand for the Anytone AT-5555 and similar radios such as the AT-5555N II and AT-55555 PLUS. This should also work with other radios like the Stryker 955HP. Look at images/files closely before deciding it...

Not finding a good mount for my Anytone 878 in my Jeep Wrangler JK, I designed an adapter to slip over a VersaMount2 with a pressure fit. So far, it's held up to a couple of trails, but throwing a little glue on there wouldn't hurt...

HR Richter mount for Anytone Handhelds

Side chasis mount mic holder for anytone 578

Stand for the AnyTone D878UVII for the Skoda Octavia mk3, or any other small(ish) cupholder. ...

Anytone AT-D868 and AT-D878 Bike Mount Have a blast melting it down

This thing is Anytone AT-778UV / Retevis RT95 HAM mobile radio fan holder. ... Need M5 nut and 30~35mm M5 bolt.

Adapter Holder for Anytone 878 and 868. Commonly used 16mm ball diameter fits most holders. Compatible with or without a belt clip attached. ...Also works seamlessly with a Battery Eliminator installed.

I required a stand for my Anytone 878 radio, one that could accommodate a battery eliminator connection without compromising access to the front panel buttons. Fortunately, there is ample space on the front of this stand, allowing all controls to...

Base for Walkie AnyTone AT - D878UV PLUS. This base is designed to fit the Walkie perfectly, it is just enough so that it does not come out of the base (if we take it in the car as in my case). ...The base can be put both in the radio room and in the...

A desk stand for the Anytone AT-778UV. 2 Versions available, one has mounting holes for the metal plate of a magnetic mount Diamond P610 speaker. Use M3 screws (I used Hex head self taping for the braces). Use M3 Bolts and lock nuts for the plate...

This stand is specifically engineered for use with an AnyTone AT-D868UV or AT-D878UV radio. Its primary purpose is to fit snugly into a car cupholder, thereby preventing the radio from toppling over and making it more stable. Additionally, the stand...

Adapter Holder for Anytone 878 and 868 Devices. Compatible with standard 16mm ball diameter holders. Designed specifically for use with belt clip attachment. Smaller in size compared to the previous version, omitting a cradle feature. ... Also...

I needed a stand for my Anytone 878 radio that could support the radio having a battery eliminator connected. There's enough room on the front that all the front panel buttons are accessible. ...The cable from the battery eliminator goes down the cutout...

This is a battery cover for a AnyTone 868/878 series 3100mAh radio battery. It protects the live contacts on both sides of the battery from getting shorted when tossing it into a bag.</p><p>I printed it in ASA and PLA. ...Both worked well, but I'd...

Side rails for Anytone AT-778UV dual band HAM radio. Since radio has only one mounting screw on each side, I designed in a plastic shelf to keep the radio stable on the side rails. It looks like the radio uses 5mm mounting screws. I've got some...

Fellow amateur radio operator was needing a mobile mounting solution for his BT-01 "remote head" for the Anytone 578. I designed this to be a more secure fit than the solution he had come up with. This mount works with 2 hole standard AMPS...

Habe eine Halterung für mein Anytone 878 entworfen. Im inneren befindet sich ein kleines Modul mit einem TP5100. Dort habe ich den 100 Ohm Widerstand entfernt, um auf einen Ladestrom von ca. 600 mA zu kommen. Außerdem muss noch eine Brücke gesetzt...

Ein vorbereiteter Standlader für das Handfunkgerät Anytone AT-D 878 UV. Es sind noch keine Löcher für die Kontakte integriert, da es zu viele unterschiedliche Möglichkeiten dafür gibt. Diese können individuell angepasst werden. Auf jeden Fall ist...

... **Important Note:** This cup holder is designed specifically with the 3100 mAh battery in mind, which comes standard with the Anytone AT-D878UV Plus handheld radio. **Additional Note:** Currently, this design does not accommodate a belt clip.

Not meant to be printed. ...This is an accurate recreation of the bracket for reference use in models.

Remixed the knobs to perfectly match my 878 UV model, and also incorporated an additional notch specifically designed for the volume control. ...I printed these using support material only on the sides, while leaving the center post hole uncovered.

Ring Spacer.

The original knobs are awkward. No problems with that :) They have been designed to make printing very easy. It does not require any additional settings. A flat surface does not affect usability, but facilitates printing. The knobs are pressed...

Not meant to be printed. This is an accurate recreation of the bracket for reference use in models. ... Category: Replacement Parts

A sleek and compact base to hold your Anytone AT-D868UV handheld ham DMR radio in place, crafted from the ingenious design by Resago's tabletop radio stand for small two-way radios.

This mount allows you to install a 120 mm computer case fan on top of the Anytone 578 radio in either pull or push orientation. My setup is configured to draw heat away from the heat sink, which has proven effective. To secure the fan in place, four...

This is a stand for the body of the Icom 2730 or Anytone AT-5888UV or any other mobile radio where the mounting holes on the body are spaced 50mm apart. It positions the radio at a 10 degree incline when placed on a level surface. I printed with 3...