anycubic x 3d models

Thank you for the original design https://www.thingiverse.com/thing:4594101 I redesigned the places where a brass thread insert fits. To make it easier to upgrade without special hardware. Attention, due to the change, other screw lengths are...

Hi, I working on a BL Toush mount for rianocerous direkt drive that is used in our fablab. not tested yet (!) , but should work. V2 (which can be seen in the picture) was too close to the print bed and was pushed up with the help of a hot air...

***Disclaimer*** I recommend using a 2.6mm spacer, but have included thinner along with photos of how they fit. These all fit with the original screws. ... If you want to make it thicker and give yourself more wiggle room then just size up the Z axis...

This is a Remix of https://www.thingiverse.com/thing:4328596 and https://www.thingiverse.com/thing:434600. Screws needed: 7x M3-nut 5x M3x16 2x M3x8 Only the sphere rod was printed with brim. ... Fan guard: https://www.thingiverse.com/thing:2505568

Increased the height of this spacer to allow for a thicker barrel jack (10 mm) to be inserted. ...Without this my lid hit the top of the barrel plug and didn't sit flush.

Remixed to mount the fan directly onto plate/cover with the housing from original. (Noctua 92x14 in the case. Fan should be mounted on the OUTSIDE. ...

Just a remix and tweak of the case design by kcmj to fit the W1209WK temperature controller. I have not included the back cover as it is available from the original author kcjm. The cover does actually need to be fixed as it won't print properly as...

Thank you for the inspiration: https://www.thingiverse.com/thing:4500307 I modified the Raspberry Pi 7" touchscreen mount to fit to the top of the frame. Included are support arms for the left and the right side of the 7" Pi screen. ...You need 4...

Repaired all the files as most of them did not slice properly in Simplify3D. Cable chains were fine, but i added them so all files can be downloaded in the same place. ... Follow instructions form the original file...

This is a Remix of https://www.thingiverse.com/thing:4328596 and https://www.thingiverse.com/thing:434600. Screws needed: 7x M3-nut 5x M3x16 2x M3x8 Only the sphere rod was printed with brim. ... Fan guard: ...

100% infill 0.1 layer height

Designed this to go with https://www.thingiverse.com/thing:4555831 and used his blank baseplate as a template. ... As of upload I'm printing this and crimping terminals.

Not using a flex-plate on this printer i got tired of holding the build plate and putty knife and hammering off the print, all with 2 hands. so i designed this stand. ...the build plate is held vertical with no force being placed on the leveling bits.

<p>Done quickly in tinkercad. ...&nbsp;Works, but could do with being designed from scratch in CAD.</p>

Remixed the original Thingi as there was no hole for the temperature probe.

Repaired all the files as most of them did not slice properly in Simplify3D. Cable chains were fine, but i added them so all files can be downloaded in the same place. ... Follow instructions form the original file...

Same file as the original make (great design!) I just flipped the heater around so the power button was in front and the intake faced the resin vat.

Hello, I've recently got an Anet A8 3d printer from my friend to fix it up. His nozzle was clogged so I wanted to buy a replacement and oh my good they are so expensive in my country so i decided to use my e3d v5 hotend and whole mk4 carriage system...

3.8mm Z-Axis spacer for the Anycubic Mono X 6Ks to work with the Wham Bam eXTReme line Flexible Build System for Resin (FBSR). Just unscrew the two machine head screws under the Z-axis sensor paddle. Insert your printed piece (in resin or with FDM)...

Hence I made this easy to DIY Anycubic Mega X Enclosure with cardboard, plastic and EVA foam for temporary use. Could be upgraded to acrylic in the future. The special features are: 1. Electronics in base are fully exposed to air to allow normal...

M3 x 12mm - Je Seite zwei Stück für die Befestigung der Halterung am Rahmen des Anycubic. Insgesamt 4 Stück.
 Vier Muttern M3 - Je zwei Stück pro Seite für die Befestigung der Halterung am Rahmen des Anycubic. Insgesamt 4 Stück.
 Druck: Support...

This is RERF (Resin Exposure Range Finder) File, made specifically for the Anycubic Photon Mono X. The other RERF Files I found here usually had certain properties that made them unattractive to me. From the good old OG Photon V1 days I know and...

Anycubic direct drive extruder mod plate, remixed to fit the Bondtech LGX-L extruder correctly, and add some reinforcements to avoid bending with time. ... Although I'm using an MK4 carrier, it also works with the stock one.

Anycubic direct drive extruder mod plate, remixed to fit the Bondtech LGX-L extruder correctly and add some reinforcements to avoid bending with time.Although I'm using an MK4 carrier, it also works with the stock one.Do you like my models? ...Consider...

The construction file *.ipt made with inventor, the *.stl file and a *.gcode file, made with Cura for the Mega X. Summarized you only need to print my part and order the new fan. No additional parts needed. ...The difference in noise is remarkable.

This is a bracket that will snap on to the top rails of the Mega X. it has a T-slot channel if you want to mount something up there, but I also added a screw boss on the front that takes an M3 nut from behind. This allowed me to mount my...

With the new endstop holder you gain 1 cm more print space in the X axis. And with the new pantine holder 2 cm more print space in the z axis have fun ...

The small black feet on the base of the Anycube MonoX resin vat often fall off and get lost. Decided to just peint replacements. Used a Form3 printer and their Flexible V2 resin. Could be printed with anything I would guess. ...Also fits other...

Dies ist ein Rollenhalter mit sehr geringem Reibungswiderstand, weil er als Rollenlager ausgeführt ist, der einfach auf den vorhandenen Rollenhalter vom Mega S und Mega X aufgesteckt wird. Dadurch wird der Extruder entlastet und die Druckpräzision...