anycubic wash and cure plus 3d models

... with double diameter of sphere that adapts according to the weight applied. The support base (made with PLA) only increases 4 mm. The height of the machine plus 12 of the shock absorber, total 16 mm, with very good surface grip and zero slip.

It works very well, but it is very noisy and only a little better than the much simpler modification of the duct on the standard ANYCUBIC blower: ANYCUBIC Kossel Delta Filament Cooler (Fan Duct). The external blower air jet mount is shown on the left...

I've got a whole collection of 120mm PC fans that I've been using to cool down the stepper motor drivers and mainboard on my Any Kossel Plus. The housing I made for them fits perfectly, so you won't need any screws to get it installed. This design is...

Anycubic calls these belt tensioners, and I'm using them now. Be careful not to over tighten the belts. The connecting rod mounting points are 52mm apart. You don't need copper spacers. I removed original carriages and placed them next to new...

It's a brand-new cooler inspired by the original design, I wanted to make some significant changes but ultimately started from scratch using dimensions and overall size from the original model. This new version is lower profile, doesn't apply as...

Hello here I leave small utensil that I solved a problem in my kobra plus, I guess it will be valid for all models with the same hotend, the movement of the head in a few days I stopped turning on the light that has the hotend and I realized that by...

I basically just extended the length and widened the holes to make it compatible with the plus model. I also modified how the 3mm screw is secured, creating a captive nut pocket on the back side of the mount. This way, if you accidentally...

Printer filament holder for 1kg spool mounted onto the top rail of Anycubuc Kobra Plus. Slightly longer screws are needed to replace factory screws. ...

Simple holder for Small hercules glue stick.Designed for anycuboc linear plus but it is possible for any 2020 profile.

Depth is 6.1mm, so fits both the shallow (untested) and long variants.this replaces the endstop screw with an M3 (use whatever you please)Carriage screw holes changed to counter sunk M3x12I realized my original Anycubic carriages had some play,...

... temperatures after that to melt, otherwise issues will arise later on. This part was designed specifically to fit with the standard Anycubic hotend, which has the nozzle approximately 17.3mm away from the metal block holding the hotend in place.

Triple exhaust port design, internally angled in such a way that air is blown underneath the nozzle rather than directly on it - my setup has the concentration point about 2mm below the nozzle, allowing seamless integration with the stock effector...

I have tried a couple of waste bins and tool holders designed to fit the Kobra Plus that actually do not fit (clearance issues) so I decided to take a stab at making one. This was designed in OpenSCAD and I am a total noob with 3d design, but after a...

I have tried a couple of waste bins and tool holders designed to fit the Kobra Plus that actually do not fit (clearance issues) so I decided to take a stab at making one. This was designed in OpenSCAD and I am a total noob with 3d design, but after a...

Allows a smooth drainage of resin from the Vat into its bottle using the Wat'n Cure as a support system.

However as i mention the original ones have also some variances in since (not to mention the play of the eye ball bearing)I try some version butSpecs :267mm lenght10x5mm magnets (N52)10mm mag ballsPrint SettingsPrinter...

Top filament spool holder for my Anycubc Linear Plus. This is similar to other spool holder you can find here like: https://www.thingiverse.com/thing:1989704 Two parts to fix on the top, the middle just clips between as a bridge, the weight of the...

... your extruder to define a position for manual bed leveling without relying on software like Pronterface. ...Use the following G-code commands to set up the shortcut: Position 1: G1 Z0 X0 Y90, Position 2: G1 Z0 X78 Y-45, and Position 3: G1 Z0 X-78 Y-45.

I don't like incompleteness of the top part of rails and created a simple cap for a better view and probably for emergency stop of carriage ))

I just wanted to pass along a simple phrase - have fun and enjoy!

Mounts specifically designed for the 23cm heated bed offer precise height adjustment capabilities, facilitating rapid and accurate bed leveling.

I sought fresher air on my right flank and yearned for clearer visibility on the left side.

... mod to the centre spool holder. ...I also decided not to print two shafts for the bearings and instead used a single 6mm x 70mm threaded rod I had on hand. Might make 4 holes and have 4 bearings not sure yet. ...Smaller reels want to fall to one side.

... independently in any location. The front cover and pad mount were printed with 0.2 mm layer thickness and 100% infill density. ...The remaining components were printed with 0.4 mm layer thickness and 20% infill density to accelerate printing time.

It's ridiculously simple! ...Just install the standard Cura driver called DeltaBot and input the values shown in the pictures. ...Done.

================================================== The goal is to create a corner cover, along with a heated bed holder and corner support, all in one piece - 3 in 1. Modified: 2018-04-06. The corner size has been repaired, and the bed holder...

This entire assembly comprises three distinct parts: the base plate, the upper clip used to adjust diameter and secure the build plate in place, and the socket, which enhances overall stability. ...Assembly is straightforward; I printed all three...

We printed ours in our Black ecoPLA Tough filament at 0.2mm layer height and 100% infill** ONLY SUITABLE FOR 0.5L BOTTLES **

... me to take on the task of crafting a brand-new one. ...This updated model stands noticeably taller than its predecessor and boasts a sleek, direct route all the way to the nozzle. ...The result is a system that functions seamlessly and efficiently!

... or as in the photos a small spring can be attached. As a result, the play and the resulting noise is significantly minimized. I recommend to fix the clips with glue, because they can slobber while printing. ...For this I used some 2 component glue.