anycubic wash and cure plus 3d models

Wall mount accessories holder for Anycubic Wash and Cure Plus

I needed an insert for a new wash and cure plus tub, and the model by JustinX was close to what I wanted. ...I remixed it to fit the photon m3 build plate and so far it seems to do the job.

I needed an insert for a new wash and cure plus tub, and the model by JustinX was close to what I wanted. ...I remixed it to fit the photon m3 build plate and so far it seems to do the job.

Made this adapter for Elegoo Saturn Build-plate to fit the Anycubic Wash and Cure Plus... Despite what they say in the ads the platform the Saturn build plate isn't very stable. Hence these. There are two different models, one for the upper cage and...

STAR WARS

What I found out is that the mighty's build plate has enough wiggle room for it to move and with the right angle and distance can fall in and damage your print. The purpose of the adapter is to remove the possibility for the build plate to move. ... ...

Adapter für die Elegoo Platform Mars 3 in der Wash and Cure Plus Station von Anycube Der Adapter passt in alle drei Positionen. Bauteilhöhe Korb unten ca. 70mm Bauteilhöhe Korb oben ca. 160mm Bauteilhöhe Korb Adapter max. Platte ist mit PETG...

platform for Anycubic wash and cure plus . staceble print with 15 outline/perimeter and 0 top and bottom layers . ...use fast honeycomb infill 6%

this is a simple bracket for the mirror foil that comes with the Anycubic wash and cure plus

This is used for making a replacement metallic vinyl sheet for a anycubic Wash and Cure Plus You can also use this for a plasma cutter to make a plexiglass sheet to put down to protect the metallic sheet.

This funnel adapter allows the use of a common coffee filter (or better yet, some polyester 400 micron mesh stapled into a funnel) with the AnyCubic Wash and Cure Plus tank. Simply run the UV cure cycle on the alcohol tank to precipitate the...

( https://www.printables.com/model/377577-drehtellerhalter-fur-anycubic-wash-and-cure-plus ) Please take note of the screen shots of slicing orientation as this is how it was designed, for strength and minimal supports. The "W&C_Plus_Insert" file...

Drehteller für Wash and Cure

Used For AnyCubic Wash & Cure Plus

Simple tray holder for the Anycubic Wash'n'Cure Plus.

ANYCUBIC Wash and Cure Drip Tray after you've washed your prints, dont you wish the basket would sit on top of the wash bin so it could drip dry? Now you can, easy to print strainer allows you to rest basket or parts over the wash container and...

ANYCUBIC Wash and Cure Drip Tray after you've washed your prints, dont you wish the basket would sit on top of the wash bin so it could drip dry? Now you can, easy to print strainer allows you to rest basket or parts over the wash container and...

Ich habe die Idee von verschiedenen Werkzeugen, um ein Modell im UV-Licht des anycubic Wash & Cure-Geräts zu halten. Die rotierende Platte ist oft frustrierend und deshalb werde ich verschiedene Kleiderbügel und Befestigungswerkzeuge für die Modelle...

I often found myself struggling for space when trying to cure large prints in my wash and cure plus. I was honestly quite surprised no one had designed one of these things before, so I did. This is a very basic device that will shift the mounting...

AnyCubic Cure Station here. Plate clearance seems low. Raised it slightly to improve exposure. ...Adjustment made, awaiting verification.

my wash and cure plus hood modification . to make it easier ta access the work area when the station is on shelfs . ...I used all original bolts except one on the back of the hood .all these brackets go on with no adjustment to lower part of station

... as pieces were falling off mine; I suspect mine might be a bit loose, so I super glued it in place - use caution, however, as this can cause fogging on the plate. Additionally, a thicker cure plate bracket and a power supply bracket are required.

This design is not usable as the measurements are incorrect, and I came up with some ideas that didn't quite work out: - Raising the machine to an Orange 30 height by adding approximately 2.5cm of height could be a viable solution. - Allowing the...

Mount to hold the curing platform of a Wash & Cure Plus when washing resin prints.

This is a replacement basket / strainer for the Anycubic Wash & Cure Plus station. Make sure to print using a chemically resistant material because the IPA will degrade the plastic otherwise. ... I have another lighter version in development that...

... and actually performs better than the original. ... Print with at least 3 walls and 20% infill to keep the magnetic weight screws from pulling out.  I printed in PLA Pro with a .3 nozzle and .2 layer height and everything works perfectly.

Insert vor ANYCUBIC Wash&Cure Plus, printed in petg and ABS. petg and abs are the optimal materials, as they react little or not at all to bioethanol and only little to isopropanol Green Version for Creality Halot One Plus Black Version for Elegoo...

Just a quick design I made to keep my Wash & Cure from becoming a miniature blender and destroying all my prints. This just simply sits on top of them and keeps them from moving around too much. ## NOTE If using an FDM printer, this needs to...

Purpose: I've had many resin prints roll or vibrate off the stock Anycubic Wash and Cure rotating platform. Also, the stock platform is smaller than it needs to be (it can be 1 inch larger). So, I designed a simple drop in platform expander with a...

Just a simple stand for the Anycubic Wash and Cure curing platform.