anycubic vyper upgrades 3d models
80888 3d models found related to anycubic vyper upgrades.
cults3d
Anycubic Vyper Upgrade kit with extendable coil clamping system for internal diameter differences. A bearing system with large planetary gears with a 2 mm module. Axle support. 55 mm riser for improved viewing comfort. Z-shaped locking system with...
prusaprinters
Not sure how well the differences come across in the pictures, but in person the differences were significant.I am unsure if this design would also work on the Anycubic Kobra Plus or Kobra Max, but since they appear to have the same X-carriage...
thingiverse
This is my try to build a low noise upgrade for the Vyper. Using printed parts for the mainboard cover and powersuply. Made it to use Noctua NF-A9x14 Fans. Minde that they are 12V so you need Step down converter. Fans:...
thingiverse
Noctua fans used in the original design weren't readily available for me. I went with [be quiet! Pure Wings 2 92mm fans](https://www.bequiet.com/en/casefans/505). Attach the fans with the self-tapping screws which come with the fans. These fans...
cults3d
Also this upgrade gives a real guidance for the threaded rods. All you need is a 608 bearing on each side and mount it like the old piece, planar with the upper V extrusion bar. Add -0.2 to hole size compensation, the bearing seat could be very...
thingiverse
Also this upgrade gives a real guidance for the threaded rods. All you need is a 608 bearing on each side and mount it like the old piece, planar with the upper V extrusion bar. Add -0.2 to hole size compensation, the bearing seat could be...
thingiverse
ANYCUBIC VYPER 2021 YEAR DIRECT EXTRUDER UPGRADE.
thingiverse
I was basically trying to address two "issues" of my Anycubic Vyper: - The PSU and Mainboard 24V fans are very loud - I want to upgrade my Vyper with an OctoPrint/OctoPi setup So here is my result: - An upgraded PSU cover featuring a 92mm fan mount...
prusaprinters
If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...
thingiverse
Clip-On upgrade for the stock spool holder that comes with the Vyper. Greatly reduces rocking of the spool during printing (especially during retractions)! Easy to clip-on to the stock spool holder. Spools with smaller holes like the TTYT3D...
thingiverse
... included the bushing needed to slip on the Z-rod. Overall super happy with the upgrade as it eliminates the rod slap on some prints. ...I'm a newb to TinkerCAD which is what I used to edit so it may not be perfect but seemed to line up well for me.
thingiverse
Remix: https://www.thingiverse.com/thing:5020211 --------------------------------------------------------------------------- Anycubic Vyper - Adapter for V6 E3D v.1.0 upgrade Annoyed by the eternal reworking of the adapter from RyanMaverick, I...
prusaprinters
DEUTSCH:Anycubic Vyper - Adapter for V6 E3D v.1.0 upgradeGenervt vom ewigem Nacharbeiten des Adapters von RyanMaverick, habe ich den Adapter nochmal nachgearbeitet und den unnötigen Steg herausgenommen.Nun passt der Adapter ziemlich gut (auf jeden...
prusaprinters
DEUTSCH:Anycubic Vyper - Adapter for V6 E3D v.1.0 upgradeGenervt vom ewigem Nacharbeiten des Adapters von RyanMaverick, habe ich den Adapter nochmal nachgearbeitet und den unnötigen Steg herausgenommen.Nun passt der Adapter ziemlich gut (auf jeden...
thingiverse
The Anycubic protective ring on new Printhead for the hotend must be removed. It is best to print the adapter and the air case with PETG. The two FanDucts are optimized for the Revo, the original ones work just as well. ... Also with PETG The...
prusaprinters
23.06.2022 - New Version This is an extension to my modular print head, see here: https://www.thingiverse.com/thing:5277900 Currently without the possibility to attach the LED. The Anycubic protective ring on new Printhead for the hotend must be...
thingiverse
Anycubic Vyper hotend upgrade, adapter is for a Phaetus Dragonfly BMO
thingiverse
This is a resized cable clip for the Anycubic Vyper upgraded Hotend cable. ...The new cable is a little wider than the previous cable hence the clip is designed to be wider as well as a little loose.
thingiverse
Filamenthalter für den Anycubic Vyper. ... Filament holder for the Anycubic Vyper.
thingiverse
Designed to fit the Anycubic Vyper original mount.
myminifactory
I designed this Camera Tripod that you can mount on your Anycubic Vyper!DIY Video: 4 Upgrades for my Anycubic Vyper Bolts and nuts you need to assemble this tripod: - 2x M5x12 Bolt- 3x M5x20 Bolt- 3x M5 Nut- For the camera attachement: 1x M4 Bolt and...