anycubic vyper print head 3d models

Print Settings Printer Brand: Anycubic Printer: Predator Rafts: No Supports: Yes Notes: I would recommend using a material that can tolerate high temperatures, such as PETG or ABS. Supports are only needed for the very top piece, and I find that it...

This is my updated design regarding the Ring LED Head Light Support for Anycubic Predator 3D Delta Kossel Printer. This support now also works seamlessly with the new fan duct, which is higher than the original one (link:...

Das ist ein Remix des ANYCUBIC i3MEGA HeadConnector Cable Holder von enry68, welcher auch für die neueren Versionen des I3M mit Ultrabase passt (mit dem grünen Stecker). Außerdem ist die Version speziell am Übergang stabiler ausgeführt und bricht...

Since the head is close to the heater cartridge, I recommend printing this in PETG or ABS (or any other material that can withstand high heat). **Update 1 (2020-07-13):** A taller "pusher" piece was added, and it's easier to print. It doesn't have a...

This is a remix of [ANYCUBIC i3MEGA HeadConnector Cable Holder](https://www.thingiverse.com/thing:2267522) by [enry68](https://www.thingiverse.com/enry68/about), which fits on newer I3 Mega's (with Ultrabase) with the green connector. It is also a...

Adjusting the towers is a task that can be streamlined by using fingers, and the screw head's small size poses a challenge. This cap fits snugly onto the original screw's head. Despite its compact nature, this component significantly accelerates...

Should be perfectly able to print without support, but it you do leave it turned on only a very tiny bit underneath the bottom hole will get supported and I doubt you would be able to tell the time difference. Recommend installing the two...

Adjusting towers is easier for me when done by hand and fingers, as the screw head is too tiny. This cap fits snugly on top of the original screw. Although small, this piece accelerates tower leveling significantly. Please add this file to...

Specifically, the cable from the heating head was passing directly through its center, causing the filament tube to bend around it in a curve. This resulted in a slip-stick effect, which needed to be corrected. To achieve this, I redesigned the cable...

They claim you can print another 3D printer using one, but this particular component is causing problems for me.\r\n\r\nFortunately, the design is quite precise, making it perfect for scaling down to create a functional keychain.

Bushing to take up slack on z axis drive screws on AnyCubic Vyper 3D printer

Anycubic Vyper tool box

Hello everyone, today I'm excited to share with you how I overcame the challenge of printing in multiple colors using my Anycubic 4Max Pro printer. Although this printer comes equipped with its own Marlin-based firmware, it lacks a standard command...

I designed this bin and legs combo because I was tired of the filament drips and pieces going into the left side rails. The legs snap into the rails, and are intended to be somewhat hard to snap in so they don't move at all once installed. The bin is...

<p>You can find the instructions in the PDF</p>

Material PLA+ Infill 40%

Customized version of https://www.thingiverse.com/thing:3294615 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3294615

Customized version of https://www.thingiverse.com/thing:3294615 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3294615

Customized version of https://www.thingiverse.com/thing:3294615 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3294615

Support for the filament spool axis. Height 137mm to the axis. ... The spool can no longer come out of the axis.

Ich habe den Halter für die Verwendung der Logitech C270 HD Kamera angepasst. Grundplatte zur Befestigung am Drucker und Arme wurden 1:1 von @McGonzo übernommen und hier direkt mit verlinkt. ...

This is a Remix of the LED Light Bar Holder from: https://www.thingiverse.com/thing:5172232 [by kiteboarder1980] for using M3 T-nuts and countersunk screws, e.g. M3*6mm, instead of a slide-in part. ...

The Z spindle is perfectly stored at the top. You need two F688ZZ or 688ZZ. ... You can also choose a lid with more grip.

one Holder for Filament on Top and one for Filament from down Bearing 608

just played around a bit my work is bad and needs a lot of support material and Improvements. ...Remix and fix it to your desire

This pops in on the top Use your existing spool holder to rest on this. ... You will also need to change the angle of your filament sensor.

Abdeckung für die V-Slot Schienenfront für alle die das Display entfernt haben. Habe die Fusion 360 Datei angefügt, somit können auch Initialen oder ähnliches eingefügt werden. ...

<p>There are two forked light barriers on the gantries for the Z axis. Once on the left and once on the right. On the outer side of each is a small grub screw with a hexagon socket. If you turn it carefully, the long lever moves up or down. This...

Remixed to be able to mount a Pi cam HQ to the case I found. ... Pi 4b housing is held together with the camera arm mount and the V-slot mount (no additional screws) Cam mounting is with 4x screw M2.5 x 10mm & M2.5 hex nut (I used M2 and got it to...

<p>Onshape model: https://cad.onshape.com/documents/65ede40b24f5475b03a657b5/w/b61737489ce3883fe20f99e9/e/08067fb49c04efd261b3984d</p>