anycubic vyper filament 3d models

AnyCubic Vyper filament sensor fix Install with 2xM3 25mm.

This is a remix of the Anycubic Vyper Filament Guide (https://www.thingiverse.com/thing:5345173) by Salamattder. I adjusted the piece so it does not require any additional hardware. Instead, it just slides into the top rail once you remove the endcap...

After top mounting my filament on the Anycubic Vyper, I noticed it would catch and snap back on the corner of the Z axis bar. ... I designed a guide to top mount between the two top screws using a 3mm x 10mm screw using DaVinnci2000s nut to lock into...

After top mounting my filament on the Anycubic Vyper, I noticed it would catch and snap back on the corner of the Z axis bar. ...I designed a guide to top mount between the two top screws using a 3mm x 10mm screw using DaVinnci2000s nut to lock into the...

This part uses Vyper's default holder. ... Most printed filament holders will tilt over time. ... Therefore, I designed the shaft to tilt a little from the beginning, considering the tilt of the shaft due to the aging of parts.

On my A-Vyper, I feed the filament from the bottom of a box. I designed the guide to bridge the angle. A PFTE tube can be fed through the hole. The filament is fed directly to the sensor. The two holes on the filament holder can be used to fix the...

Stabylizer for the original Anycubic Viper Filement Holder.

Original Make: https://www.printables.com/model/126420-anycubic-vyper-filament-spool-holder-with-bearings Original Maker: https://www.printables.com/social/211918-nano3/about The original is a great idea. The bearings work like a charm. I've been...

Allows mounting the Anycubic Vyper's filament sensor at a 45° angle to reduce strain on the sensor when the filament spool is mounted on the top instead of on the side. Prints nicely in PLA without supports (see picture with print orientation) in...

A filament garbage collector for the Anycubic Vyper.

HW I'm using to mount this: - 2x M3 16mm bolts for the base - 2x M3 20mm bolts (sensor housing) - 2x M3 nuts (sensor housing) Printed on Anycubic Vyper, with PrusaSlicer, using Creality CR6-SE profile with modified bed size. ... 205C extruder temp,...

... sensor to the filament tube so I would not have to guide the filament every time I changed it out...so this is the end product. ...Yeah, there is probably an easier way, but what fun would that be... Designed in Fusion 360 Printed on Anycubic Vyper

I designed this holder replacement for my vyper because with a lot of retraction the runout sensor bends in an unhealthy way. Even more when there's not much filament on the spool so the angle to the sensor intake gets very steep. That's why the...

I designed this holder replacement for my vyper because with a lot of retraction the runout sensor bends in an unhealthy way. Even more when there's not much filament on the spool so the angle to the sensor intake gets very steep. That's why the...

Sensor holder for spools on top of the vyper. It fits highest Z position. Stock screws for the holder itself and 2 M3x30 for the sensor + nuts of course. Print from any material you like. ... No supports needed.

Uses a bearing from a hard drive.

Anycubic Vyper Filament feeder with roller for top mounted filament. ... Screwless design.

This is a mount to move your filament runout sensor on an Anycubic Vyper for a Direct Drive configuration!

Designed a 45° filament sensor mount for my Anycubic Vyper because my filament spool is mounted on a wooden casing. ...Added some extra holes to save filament, should be stable anyway.

This filament holder is for the Anycubic Vyper .... well known from the Ender 3. You still need two 608ZZ bearings. The design was taken from chickensaretoobig (see remix) as it is the same spool holder adapter. The adapter has been realigned...

I designed this to top mount a filament spool on the top rail of the Anycubic Vyper without the use of any additional hardware. To install just remove the top rail (4 screws), slide the mount on, then reinstall the top rail. If you use a top rail...

I put my new anycubic Vyper into an "enclosure", that had no space for the long arm, that holds the filament. I hat to switch to a short arm that holds the filament closer to the Printer to reduce the footprint. This way however the printer has to...

You want to feed your Vyper with filament through a bowden tube? With this new filament holder design, you can stick a bowden tube into the filament sensor input and feed your filament from a distance.Replaces the old tiny metal bracket. You need a...

The original file creates some tension between the filament and the sensor. ... This remix solves this issue and it still compatible with the default sensor wires.

When you plan to position your filament spool above the printer you might need an adapter, which makes it easier to extract the filament from above. This is a remix. Thankyou for the idea You might need an extra M3 screw and a M3 nut. The screw...

Maybe this is due to the fairly long PTFE tube connected to my filament box. So I made this stronger holder to replace the original flimsy holder. Two m3 x 12mm screws was used to secure the holder to the printer. ... One m3 x 18mm screw and...

Ein für meine Anprüche benötigter Halter für den Filamentsensor, um meine in Samla-Boxen gelagerten Filamente direkt am PTFE Tube anschließen zu können. Er stützt sich sowohl oben, unten als auch seitlich ab, was ihm etwas mehr Stabiltät verleiht. ...

Anycubic Vyper Filament Sensor Holder with 608 Bearing. - one Part for Original Extruder - one Part for Original Extruder Filament from Top - one Part V2 for Micro Swiss Extruder - one Part for Micro Swiss Extruder Filament from Top The tab on the...

Anycubic Vyper Filament Holder with Extruder hot end cable clip. Remixed from both JBDoge (thing: 5173089) and pmatsol58 (thing: 4939641). Combining the Hot end Cable clip with the Filament Runout Sensor Bracket / Holder. Needs : M3 x 16 -...