anycubic vyper fan duct 3d models

The Anycubic 4MAX boasts a fan duct specifically designed for a 30mm throat.

This part is and add-on to the excellent design by DerLatzer : https://www.thingiverse.com/thing:4974423 It allows the use of the stock fans 4010 fans that came with the printer. I opted to go this route due to the vibrations from the 5015, and for...

Simple Anycubic i3 Mega S fan duct for stepper driver upgrade to TMC2208 with use of standard 50x50mm cooler.

Use this to calibrate the z-offset on the Anycubic Vyper printer

Anycubic Vyper hotend upgrade, adapter is for a Phaetus Dragonfly BMO

Simpe, non-destructive riser feet for AnyCubic Vyper's silent fan modifications. You can use the original rubber feets, these parts only a spacer between the printer/spool holder and the rubber parts. Simply remove the rubber feets, leave a glue...

A screen cover to protect it and eliminate the light from the room for the ANYCUBIC VYPER printer.

You can find this and other projects at https://www.tinkercad.com/things/03NEJunad0e-anycubic-i3-mega-s-fan-stock-drivers-duct. ...Thanks for checking it out!

Made for the Anycubic Vyper with Stock Hotend. Works finde for many Hours now. i printed it with an 06 Nozzle. But 04 ist better for the details i think. The Original LED is used for the "V" Logo. You can mount one or two 5015 radial-fans. ...

The  mount fits to this cable chain: https://www.thingiverse.com/thing:4935924Thats the fan duct from the picture: https://rene-jurack.de/well-engineered-hemera-fan-duct-2/I had a 40x40x15 fan lying around so I made a funnel for the...

Print part for Anycubic Vyper. I was unlucky when I received the printer from the store. the top plates that hold the fans in place were broken, so I designed some new ones. ...Happy printing :-)

Anycubic Vyper spring steel print bed guide. Makes quick installation of the Vypers stock spring steel build plate. Print snaps into place between the vypers print bed carriage and print bed. ...This is a remix of thing:5219287 by taka0909</p>

I crafted this custom holder for my Anycubic Mega-S Part Fan Duct Half-Circle (Remix) based on "SmashD"'s design, as I encountered a minor sagging issue with my PLA Fan Duct and chose not to print an entire Hotend Cover instead. ...I drilled a 3mm hole...

You have to pull the mainboard out of the case to install the fan upgrade for the fan duct into your printer, and it's a snug fit but it works.

... match and are made a little smaller than they really are. The plate is needed for easy blowing design or to try on a hotend, heating unit. Carriage plate for anycubic vyper: https://cults3d.com/en/3d-model/various/carriage-plate-for-anycubic-vyper

This adapter will work with most 90mm square box fans, adapting to 3 inch duct. ...This is designed to be printed on an Anycubic Photon printer.  I suggest using ABS resin and no scaling.

This is V3 of my Anycubic Kobra fan duct. No supports and easy print. ...V2 has helped maintain bed temps but this has helped keeping it in the same place without taping or glueing it down.

Thanks to KuRiXY for the fan duct upgrade. I reinforced the mounting bracket, as it proved difficult to print on my AnyCubic I3 Mega initially. ...The additional material provides a snug fit for the nuts, making assembly a breeze.

&nbsp;It uses the stock cooling fans from the Vyper, rather than having to solder connections for different fans. &nbsp;It also has a mounting point for the LED included on the Vyper. &nbsp;From the test prints I have done, all done at 0.3mm layer...

Thanks to KuRiXY for his Anycubic i3 Mega Fan Duct v6 with Split, just remixed it to fit perfectly on the normal Anycubic i3 Mega Hotend. Check out my closed hotend cover at https://www.thingiverse.com/thing:31474959 for a matching cover! ...This design...

This is a mount I made for the Anycubic Vyper screen. Directions: 1. Unscrew and disconnect Vyper screen 2. Using the screws you just unscrewed, mount the quick mount to the back of the screen. 3. ...Reconnect the cable and enjoy

The Anycubic Vyper has plastic bushings around the z-rods that wear over time. You can replace them with 688zz bearings, but they will still have a little slop around the bearing. ...This bushing is to take up that slack.

LED Light Bar Holder for Anycubic Vyper. ... You need this LED Light Bar (308mm): https://www.amazon.de/gp/product/B07DPJ1KXC/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1

Remixed bed handle for Anycubic Vyper For ~ 11mm spacer height between bed frame and bed Should fit tight, the original one from CLNilix is too loose for me Be careful when installing, don`t damage the heater foil !

Touchscreen relocation bracket for the Anycubic Vyper. Original placement is at the front right. ...This bracket re-positions the screen to the middle right of the machine with clearance away from the Z-axis at its lowest point.

I put this booth great designs together to create a mount point fpr my escp 32 Cam on my Anycubic Vyper. ... My version of the camera enclose may you found here: https://www.thingiverse.com/thing:5322536

Pi camera mount for the base corner of my Anycubic Vyper, flexable arm made from pop apart lube tube. ... Mounted using 10-32 machine screws in place of metric original fit great.

Design objectives: - Perfectly centered around head - Even flow distribution - Most powerful blow possible - Optimal design for FDM printing As no such fan duct already existed I designed my own. The air duct reduces its section linearly to keep...

Original posting: This is a remix of combination of Vap3Lif3_MCMXCV fan duct that was designed using https://www.printables.com/model/378928-anycubic-kobra-neo-fan-duct by Martin. ...The circular fan duct was found on the internet (no idea where I got...

Wyze Cam V2 mount for the Anycubic Vyper. Tolerance is tight, it slides back and forth on the Vyper frame, but pretty sure the PLA may break if you try to completely remove. YMMV. You could remix and add some holes in the frame to save some...