anycubic vyper change filament during print 3d models

I designed this to top mount a filament spool on the top rail of the Anycubic Vyper without the use of any additional hardware. To install just remove the top rail (4 screws), slide the mount on, then reinstall the top rail. If you use a top rail...

😃👍Additionally required parts1x M3x18 Bolt or longer1x M3 NutAssembly instructionsUnload your filament from the filament sensor to make installation easier.Unscrew the bolt on the filament sensor.Place the adapter like in the photos where the...

The original Anycubic Vyper spool holder takes too much space- so I decided to have the spool holder on the horizontal bridge. The load of the spool is directly on the left pole to avoid to much vibration on the bridge. The filament sensor switch...

I always had the problem that the filament sensor on my Anycubic Vyper was bending upwards when loading the filament from above. ...So I designed a holder for it, which is very strong and durable.Here comes the assembly instruction:Print the model...

Eine Halterung um den Smart Filament Sensor an die Vyper zu befestigen. ... A bracket to attach the Smart Filament Sensor to the Vyper.

Also has a strain relief for the tubeWhen not using the Palette, the bracket works fine for bare filament.You will need to clip off the filament sensor bracket and mount the sensor to this bracket.Parts needed:2x M3x25 Screws, Nuts, and WashersPrint...

Eine Halterung um den Smart Filament Sensor an die Vyper zu befestigen. A bracket to attach the Smart Filament Sensor to the Vyper. Print Settings Printer: Anycubic Vyper Rafts: Doesn't Matter Supports: No Resolution: 0.15 Infill: 20% Filament:...

Ich habe meinen Anycubic Vyper modifiziert, da mir der Platz für die seitliche Filamenthalterung nicht zur Verfügung stand. ... Benötigt werden folgende Dinge: 1x Der eigentliche Spulenhalter - https://www.amazon.de/dp/B08L6KKRJX?psc 1x Die angefügte...

This is a spool holder for Anycubic Vyper that has a thinner radius than the default. ...I had spools from M3D where the hole was not big enough to fit the default holder.

 Help guide the filament.Installed where the runout filament attaches to the machine.Move the filament spool to the top of the machine and need a side guide so the filament has no sharp angles to deal with.Don't use the runout sensor, so I just...

I put my new anycubic Vyper into an "enclosure", that had no space for the long arm, that holds the filament. I hat to switch to a short arm that holds the filament closer to the Printer to reduce the footprint. This way however the printer has to...

When not using the Palette, the bracket acts as a nice little strain relief guide for bare filament for normal single color prints and features You will need to clip off the filament sensor bracket and mount the sensor to this bracket. ... Parts...

Original Make: https://www.printables.com/model/126420-anycubic-vyper-filament-spool-holder-with-bearings Original Maker: https://www.printables.com/social/211918-nano3/about The original is a great idea. The bearings work like a charm. I've been...

 Help guide the filament.Installed where the runout filament attaches to the machine.Move the filament spool to the top of the machine and need a side guide so the filament has no sharp angles to deal with.Don't use the runout sensor, so I just...

Filament Guide for Anycubic VyperYou need a 608 bearing.You need longer M3 Screws for mounting.Supports are not necessary, just print with "bridge" and just punch through the M3 hole - it is a 0,2 mm Bridge Layer

You want to feed your Vyper with filament through a bowden tube? With this new filament holder design, you can stick a bowden tube into the filament sensor input and feed your filament from a distance.Replaces the old tiny metal bracket. You need a...

Since I needed my Vyper to fit into a modified kitchen Cabinet, it was necessary to feed the Filament from the Front instead from the side or the top. For this simple Filament Guide you will need: -) 7 M3*20 Bolts with a round head -) a short PTFE...

The original filament holder used too much space. ...The side spool holder fits into the top rail of the printer and uses the original spool shaft delivered with the Vyper. ...I tried to find the optimum for a minimal footprint of the printer.

Tired of the filament holder on the Vyper taking up a ton of space? I was too! I couldn't find any designs for a similar part (ones that didn't require metal screws that is) so I decided to make it myself. ...This might not be able to support very heavy...

I made this so the filament could be fed from the back.Happy printing!

The shaft diameter will probably need tweaked; I had printed mine on my Ender 3 before I upgraded, so the accuracy on that print wasn't great, but I reused that print for this and didn't change the model. You'll want the shaft diameter such that you...

I made a mount that allows you to swing the filament sensor out of the way, so you can bypass it when it isn't needed, and just swing it back to use it again. You will have to disable the switch in a terminal like pronterface or octroprint to print...

The original file creates some tension between the filament and the sensor. ... This remix solves this issue and it still compatible with the default sensor wires.

Support capteur fin de filament pour montage de la bobine sur portique Changer le guide de la vis sans fin par celui fourni, sinon le capteur va venir toucher celui d'origine.

When you plan to position your filament spool above the printer you might need an adapter, which makes it easier to extract the filament from above. This is a remix. Thankyou for the idea You might need an extra M3 screw and a M3 nut. The screw...

Maybe this is due to the fairly long PTFE tube connected to my filament box. So I made this stronger holder to replace the original flimsy holder. Two m3 x 12mm screws was used to secure the holder to the printer. ... One m3 x 18mm screw and...

Der Remix besteht aus basis von https://www.thingiverse.com/thing:5149191/files und https://www.thingiverse.com/thing:5175594/files Mich hat beim normalen Guider gestört das das Filament am Plastik "scharrt" und daher hab ich beide Versionen...

Der Remix besteht aus basis von https://www.thingiverse.com/thing:5149191/files und https://www.thingiverse.com/thing:5175594/files Mich hat beim normalen Guider gestört das das Filament am Plastik "scharrt" und daher hab ich beide Versionen...

Ein für meine Anprüche benötigter Halter für den Filamentsensor, um meine in Samla-Boxen gelagerten Filamente direkt am PTFE Tube anschließen zu können. Er stützt sich sowohl oben, unten als auch seitlich ab, was ihm etwas mehr Stabiltät verleiht. ...

Thanks to Michael Luce for printing this out for me! I will post pictures once he gets this mounted. He's waiting on some M3 hardware. ... HW I'm using to mount the original version: - 2x M3 16mm bolts for the base - 2x M3 20mm bolts (sensor...