anycubic vyper change filament during print 3d models

... and snap back on the corner of the Z axis bar. ... I designed a guide to top mount between the two top screws using a 3mm x 10mm screw using DaVinnci2000s nut to lock into the track: https://www.thingiverse.com/thing:3050607 Printed on Anycubic Vyper

Offered here is an additional filament holder for the Anycubic Vyper as a 3D printed model. The holder supports the series arm to which the filament is attached optimally and engages perfectly in it through the round flange, thus oscillations and...

I designed a guide to top mount between the two top screws using a 3mm x 10mm screw using DaVinnci2000s nut to lock into the track: https://www.thingiverse.com/thing:3050607 Printed on Anycubic Vyper Print Settings Printer Brand: Anycubic Printer: ...

This part uses Vyper's default holder. ... Most printed filament holders will tilt over time. ... Therefore, I designed the shaft to tilt a little from the beginning, considering the tilt of the shaft due to the aging of parts.

Top Filament holder for Anycubic Vyper. Designed this to mount Filament spool (1kg) on top of the printer to save some space. Due to the conical-shaped recabtable, any spool fits and is properly mounted. Adjusts itself by tighten the wing nut on...

On my A-Vyper, I feed the filament from the bottom of a box. I designed the guide to bridge the angle. A PFTE tube can be fed through the hole. The filament is fed directly to the sensor. The two holes on the filament holder can be used to fix the...

Stabylizer for the original Anycubic Viper Filement Holder.

This holder is modeled after the original. ... I have printed it 2x ud put a stainless steel rod in between to be able to use larger filament rolls.

A filament garbage collector for the Anycubic Vyper.

AnyCubic Vyper filament sensor fix Install with 2xM3 25mm.

Print both parts centered and face down on the same file to ensure they fit together perfectly, then print the details first and finally the filler part. Leave the details on the bed in between prints, set Z Hop for the filler to 0.5, and keep your...

Automatic translation into English The usual filament roll holders only fit large 80mm rolls and are hard to print. I have adapted all the parts so that they take less printing time, fit the small rolls and are easy to print. The insert with the...

... in case, but it's your call. If you need a top rail mount for your filament, here is one I designed that also doesn't require any additional hardware: https://www.thingiverse.com/thing:5407700 Designed in Fusion 360 Printed with Anycubic Vyper.

... sensor to the filament tube so I would not have to guide the filament every time I changed it out...so this is the end product. ...Yeah, there is probably an easier way, but what fun would that be... Designed in Fusion 360 Printed on Anycubic Vyper

HW I'm using to mount this: - 2x M3 16mm bolts for the base - 2x M3 20mm bolts (sensor housing) - 2x M3 nuts (sensor housing) Printed on Anycubic Vyper, with PrusaSlicer, using Creality CR6-SE profile with modified bed size. ... 205C extruder temp,...

Sensor holder for spools on top of the vyper. It fits highest Z position. Stock screws for the holder itself and 2 M3x30 for the sensor + nuts of course. Print from any material you like. ... No supports needed.

I designed this holder replacement for my vyper because with a lot of retraction the runout sensor bends in an unhealthy way. Even more when there's not much filament on the spool so the angle to the sensor intake gets very steep. That's why the...

I designed this holder replacement for my vyper because with a lot of retraction the runout sensor bends in an unhealthy way. Even more when there's not much filament on the spool so the angle to the sensor intake gets very steep. That's why the...

Recording changed so that you can insert the role from the front.

Since I positioned the filament spool above the printer, I was not happy with the filament moving the filament sensor. The sensor was pulled up every time the filament was extruded. To keep the sensor from breaking at its mounting position and to...

This a small upgrade that can help you avoid filament detector problems. ...Easy mounted without any screws and glue.

Long filament holder for anycubic vyper

**Print settings:** Printer: Anycubic Vyper Resolution: 0,2mm Support: yes I used black PETG ...PLA will also fit, of course. ** gcode - files** The gcode file is only for the Anycubic Vyper! Use at your own risk! Die gcode-Datei ist nur für den...

Filament spool holder bar for anycubic Vyper. ... To attach small spool, made for this by ABS.

This is a mount to move your filament runout sensor on an Anycubic Vyper for a Direct Drive configuration!

Hi This is a filament waste collector for the Anycubic Vyper. If you enjoy the model please consider a like, make a post or a donation! ... regards

... the way the filament sensor bends while retraction and I feed the Printer from top. ...so I create this Filament Extruder Bearing Guide for Anycubic Vyper. ... Printing: Support: Yes resolution 0,2 Infill 50% 3 of M3 x 30 2 of M3 x 16 1 of 608 Bearing

Designed a 45° filament sensor mount for my Anycubic Vyper because my filament spool is mounted on a wooden casing. ...Added some extra holes to save filament, should be stable anyway.

This is a 20mm stilt that goes on the base of the filament spool holder of the Anycubic Vyper if you're using geradedu's antivibration feet. ... https://www.thingiverse.com/thing:5379082

I designed this to top mount a filament spool on the top rail of the Anycubic Vyper without the use of any additional hardware. To install just remove the top rail (4 screws), slide the mount on, then reinstall the top rail. If you use a top rail...