anycubic predator parts 3d models

Part cooling fan upgrade. It increases the print quality very much especially if you are printing with pla. There are many very good fan ducts such as petsfang or manta but i decided to use this dual fan duct and it works extremeley great, but you...

Each standing separately as part. Adding this diamond standing, all perfect stand - to see that all these individual diamond perfectly standing giving total reaching one thousand of brilliant standing at just only the round carat type diamond with...

There it is inserted into the corresponding insert.AssemblyThe model is optimized for 3D printing and consists of three parts:Front panel with solid mounting struts (black) for the actual caseCase bottom (orange), is inserted into the strutsCase...

 There's also a bunch of comments in there, if you want to tweak the design.If you want to run off a bunch of customized OpenSCAD parts, they print reliably on my crappy printer with a small brim.  You will want to run one off first,...

Once you connect your device to it the Bluetooth icon will change to blue and the LED in the back will change to blue.If for some reason the device becomes frozen or unresponsive you can click on the flush reset button on the back. Printing:All...

You also might hit a rock and the 99% infill in the penetration point might keep it from breaking and the 99% infill at the nut would let you gently hammer it part way in to get started. I printed with PolyMax PLA. Since it will be in the ground...

eure Wünsche auf zu nehmen.@Dear Prusa Team:Don't give up the Prusa Mini and keep on developing it as the best compact 3D-Printer. Danksagung:Danke an die Entwickler von Prusa Slicer Danke an die Entwickler von FreeCAD 0.19 Danke an...

It is important to prevent overheating, as the part may become deformed. You will need an Arduino Nano board, an 8x8 color display matrix, a 200-500ohm resistor with any power and some wires. For electronics, I used the information from this site <a...

After the designs had been completed and all of the parts printed out, the printed material was not strong enough to support the water-soaked clay pellets. However, the customization abilities of the printing program allowed me to increase the...

I would encourage printing this part with a brim if you're worried about, or are having, first-layer adhesion issues - the front is quite thin. Print orientation is as the file is supplied (filter-threads on the build plate).</p> I only needed a...

http://www.thingiverse.com/apps/customizer/run?thing_id=41274 Instructions Using the following options: pillar_translating_position_x_y_z = [00_pill_location_x,00_pill_location_y,00_pill_location_z] 00_pill_length_now_is = 2.5...

Old School will likely require some servo extensions. Notes: Printed in eSun PLA+ Arrange parts on the build plate according to the illustrations. Cura: Support Touching Build Plate, Infill 15% Trim away the 2 little locking tabs inside the slots of...

You can find all of these parts on Aliexpress for close to half the price as long as you don't mind waiting a month and a half for shipping (assuming you live in the USA). Warning: buy cheap knock off items, expect cheap knock off quality prints. ...

This might take a couple of tries to get right, and is the most difficult part of this build. Using a soldering iron and two matching resistors, convert the control board of the dismantled servo into a continuous rotation speed controller. There are...

To use them split the object into parts, then print the supports with 1 bottom layer, 1 perimeter, 0 top layers, 0% infill. The supports print fast, use very little material, and should come off easily with a clean result.The supports should look...

The only measurement that seemed to line up was the inner part of the mouth, whose vertical lines were perfectly aligned with those of our print. To make the mouth wider while keeping the inside lines stationary, we moved the outer lines 0.05cm...

I wanted to have all models fit without XY Size Compensation, so I made everything with fit offset of 0.4mm for loose fits and 0.3mm for tighter fits.For the complete game you should print:PartNo.1st and 2nd level Blockx403rd level...

This will set it perfectly in the middle of the model, lowered by 0.3mm (which is half the size of the label indent, centering it with the smallest part of the model). You can tweak this Z value if you wish to have the tag closer to the front or the...

Even though Pepe was never on the original Muppet Show, I thought he'd look good in one of these, so I did one of him up as part of the purple tux mob. No supports on the body or legs. Light supports on the arms and head. BE careful with those...

************************************************************************** Parts Used: Components Required : 1. XL4015 Module :...

hex_bolt - builds a hex bolt with the part of the body optionaly not being threaded. </li> <li> hex_nut - builds a hex nut. </li> <li> wing_nut - builds a wing nut. </li> </ul> If you run openscad on this file, it will build example...

If you are looking for more, check out our premium projects: https://codeandmake.com/premium As seen on MakeWithTech Irv from MakeWithTech demonstrates how to customize this design on the Models @ MakeWithTech platform: OpenSCAD Customizer Options We...

Remix to suit your needs.&nbsp;&nbsp;This print is composed of 2 main parts along with a knob for an M6 bolt. I printed in Prusament PC blend natural white with 100% infill.</p><p>You will need the following:</p><p>3x M3 x 25mm button head...

It also can clamp down on any worn/narrower parts in the future.If you're adjusting the adaptor to go INSIDE a dust port (not recommended since it restricts airflow) then the "wider" end, will need to become the narrower one, and the "narrower" end...

In CAD, the designed clearance between the two colours is 0.1mm for a snug fit between both the horizontal dividing lines of the white and green coloured pieces, and under the green half-section which sits on the lower white 'step'.These two pieces...

=> set your user and that should be it for this part ;0) ----------------------------------------------------------------------------------------------- Klipper ---------- From a terminal(or Putty), connect to your Raspberry Pi then: - Connect your...

The paper sketch of the ghost was made in 2x scale so that any precise measurements could be marked down with more ease.The most important part of the process of building the model in Solidworks was making a center rectangle constraint box, as the...

... bracket where you like and fully tighten the three screws.</strong></p><p><strong>Per #15 Route the LCD ribbon cables under the frame and attach them. The one with two lines attaches to the connector furthest from the dial.Category: 3D Printer Parts

Since many of my friends own the 18V Makita battery system I thought of a practical Christmas present for them.I got the idea for the basic platform from user "bitplusatoms" with his design "Makita Battery Mount"...

You can pick and choose which part you want to install.I use the Ikea Platsa 600x1200x550 frame and Vard 600x1200 glass door. For the shelves, I used 295mm x 15.5mm melamine boards. You can use pretty much use any cabinet that will fit the printer;...