anycubic predator extruder 3d models

Super cheap, $0 if you have screws laying around, direct extruder for the Anycubic Mega X You'll need: -Some extra Bowden tube -2 M4x12mm machine screws and nuts -2 M2x5mm wood screws -Extruder extension cable OR extra extruder cable Tools: -Hex keys...

In any case you need a cable extension.Extruder_non_reversed.stl now contains a model which allows you to mount the extruder without reversing the motor.IMPORTANT: The motor needs to run the opposite direction (for the "Extruder_mod1" file) when in...

Upgrade for extruder

I bought a cheap MK8 extruder designed for a CR-10 from Amazon, and I used these pieces to mount it to the left side of my Anycubic i3 Mega-S. I've included two files to attach the motor/extruder itself, as well as some clips and a wire track that...

I bought a cheap MK8 extruder designed for a CR-10 from Amazon, and I used these pieces to mount it to the left side of my Anycubic i3 Mega-S. I've included two files to attach the motor/extruder itself, as well as some clips and a wire track that...

Designed a mount for the Bondtech BMG (and its clones) extruder for my Anycubic i3 Mega so it can work with the X axis cable chains with adequate clearance. For v1: Use pancake stepper motor to ensure clearance if you are using a rear mounted 5015...

... too high for the structure, so it cracked at the first angle from the top. That's why I added the reinforcement ridges. Print Settings Printer: Anycubic i3 mega Rafts: NoSupports: No Resolution: 0,2 mmInfill: 60% Category: 3D Printer Accessories

This is replacement part for Anycubic Mega S, cracked original Titan extruder lever. Compared with source, I made couple of changes: - adjusted hole sizes for better fit - reinforced parts, especially in place, where the original part had cracked ...

Upgrades for my Anycubic i3 Megaa) Direct Extruderb) Cable Chain Y Axisc) Top mount for the filament sensorV1 with the original radial fanV2 with a 5010 radial fanthe difference is only the fan mountDirect Extruder:Hotend V540x40x10 Fan Original part...

Upgrades for my Anycubic i3 Megaa) Direct Extruderb) Cable Chain Y Axisc) Top mount for the filament sensorV1 with the original radial fanV2 with a 5010 radial fanthe difference is only the fan mountDirect Extruder:Hotend V540x40x10 Fan Original part...

Here is another version of an Extruder Holder for the Anycubic I3 Mega. This one is placed on top of the printer to feed filament from the right side. Now, I have also designed a new version (https://www.thingiverse.com/thing:3223705) that goes down...

The arm or lever on the extruder of my Anycubic i3 Mega S snapped and I was unable to manually load or unload filament by hand. It appears that the original is pretty fragile and will likely need to be replaced sooner rather than later. This upgrade...

This is a modification for Anycubic Mega-S extruder (not i3 mega). It fix flexbile filament jam between the gear and filament guide, there are big gaps between stock guide and driving gear. I did print it with 0.1 accuracy without supports. After...

This is a modification for Anycubic Mega-S extruder (not i3 mega). It fix flexbile filament jam between the gear and filament guide, there are big gaps between stock guide and driving gear. I did print it with 0.1 accuracy without supports. After...

I upgraded my Anycubic i3 Mega's extruder fans, but now I need to resolder the connectors on the PCB for this modification to work. Alternatively, I could simply relocate the PCB to a different position. To make room for the new fan setup, I created...

Hi, This is my Direct Drive Extruder for the Anycubic I3 Mega. This Extruder was printed in ABS. It works perfectly with TPU, PLA, ABS, PETG Filament. Parts that can be used from Stock: Nema 17, Extruder Rad, Feder, Druckrolle, Heathead,...

Also, you'll need to print this part: https://www.thingiverse.com/thing:2838383 to install this extruder on Anycubic I3 Mega. It may be tricky, but as you can see in the photos, it's possible. **Changelog:** - 19.06.2018 - I made a new fan mount...

ANYCUBIC i3 MEGA S BMG CARRIAGE Hello This is Direct Extruder CARRIAGE designed for BMG Dual Extruder and standard E3D V6 hotend set for Anycubic i3 Mega/Mega S. My target was to get lightweight BMG direct extruder carriage. Many of those parts are...

Semi-Direkt Extruder für Anycubic Mega X Ich habe mal versuchsweise - da ich Probleme mit der Tube hatte - auf Semi-Direkt Extruder umgebaut. Funktioniert echt gut. Lediglich die Geschwindigkeit, wegen des höheren Gewichts des Aufbaus, sollte etwas...

Designed a mount for the Bondtech BMG (and its clones) extruder for my Anycubic i3 Mega so it can work with the X axis cable chains with adequate clearance.For v1: Use pancake stepper motor to ensure clearance if you are using a rear mounted 5015...

This is a little upgrade for your stock extruder ( feeder) of the Anycubic I3 Mega M to make the filament insert a little bit easier. It's really hard to change or insert the filament with the stock feeder, and if you dont want to replace the...

Direct drive extruder for anycubic vyper The heatsink from trianglelab is used. Thermal barrier with threads on both sides. If the adapter from the heat sink to the strain gauge does not fit the heat sink then print it 105% wide and long, 100% high....

Semi-Direkt Extruder für Anycubic Mega XIch habe mal versuchsweise - da ich Probleme mit der Tube hatte - auf Semi-Direkt Extruder umgebaut.Funktioniert echt gut. Lediglich die Geschwindigkeit, wegen des höheren Gewichts des Aufbaus, sollte etwas...

The design features bolt holes to secure the extruder in place on top, and seamlessly integrates with the back spool holder (https://www.thingiverse.com/thing:2872984). Most of the bolts used are M4x10mm, but I opted for M4x8mm bolts when mounting...

I designed a handwheel for my extruder for two reasons: to see how fast the extruder spins to push the filament manualy in or out by hand

A basic Extruder Mount because my Spool sits neatly on the Wall directly above the printer.

The default direct extruder from Rudi008 broke so I made a reinforced version of it.

IN THAT WAY IT IS AVOIDED COMPLETELY ANY FLEXION OF THE WHOLE SYSTEM. Currently, using nozzle 0.6 I have retractions between 1.6 and 1.8 mm at 50 mm / s Print instructionsUnassociated tags: extruder chiron, mk8 chiron, mod chiron Category: 3D Printer...

A printer extension for the Anycubic I3 Mega that enables printing with flexible filament. ...Make sure to check after installation that the roller facing the gear can still move freely.

This is my design for my anycubic kobra go printer because I wanted to convert it to a direct drive drive.It is easier to mount because you just have to slide the other to the roller