anycubic photon zero 3d models

I am creating two versions of my rear vent duct adapters for the Anycubic Photon: a 4" version for connecting to standard ventilation tubing and a 2.5" version for connecting to vacuum hoses and smaller tubing. To install, follow the instructions on...

Crafted specifically for Anycubic Photon printers, this platform accommodates the resin tanks seamlessly. Once printing is complete, simply slide the tank into place, shielding the lower area from splashes, scratches, and dust. This way, you can...

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

This is my own try to make the vat for Anycubic Photon Mono X, since I wanted to make a drain stand for the Vat. I dont claim that it is totally exact as the original but as close as possible I could make it. If anyone finds anything wrong with it...

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

I wanted to give it a more personalized feel to this cover so I added the Photon and the Anycubic logo to it. Please notice that the area where the big logo is located is very thin and some might assume is not full uv-proof. I am fine with mine....

It's compatible with Epax-X1 and Anycubic photon vats, possibly other models as well. I built this using 10mm aluminum pipe for the legs and 8mm pipe for the rotating pins, which I happened to have on hand. The funnel holder is made from M5 screws,...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be exactly ten of them. The ridges are a precise 0.25mm wide and 0.5mm apart. For each one missing, you're losing a significant...

This accessory, designed to replace the upper glass of the Anycubic photon printer, will draw in part of the odor emitted by the resin during printing and, with a rubber tube properly connected, discharge it outside. For example, allowing the tube to...

This is the DIY carbon filter for Anycubic Photon Mono SE. It should reduce some resin fumes.The factory carbon filtration of Photon Mono SE doesn't work quite well. Two fans push fumes from build area through the activated carbon sponge to the...

I liked IKE_144's remix of Ermai's build plate holder that makes it so you can angle your Anycubic Photon (or Qidi Shadow 5.5s in my case) build plate over the vat to help with dripping from different angles. My printer doesn't do bridges very...

@DocTanner crafted an innovative Rear Vent duct adapter for the Anycubic Photon, available here: https://www.myminifactory.com/object/3d-print-64661. I sought to enhance this design by adding a feature that would allow me to incorporate filters...

Rear bulkhead of the Anycubic photon is a crucial component that requires precise installation. Two versions are available, one identical to the original and another adapted specifically for the ethernet connector. Key steps include preparing the...

This is designed for straining and collecting debris from anycubic photon vat systems. It can be particularly frustrating to go through the straining process after encountering failed prints, especially when the hardened resin is not visible at all...

This device is designed to be attached to the Anycubic Photon, specifically aimed at reducing the smell from resin use.\r\nA brushless fan with an 80mm diameter should be installed between the panel and the box, secured in place using m5...

My Anycubic Photon S has 2 exhaust fans in the rear of the build chamber. These exhaust fans have housings on top of them with small bags of activated carbon inside. This filter box is simply a container with holes in the bottom that are small enough...

Hi!I made this for my Anycubic Photon Mono SE. This is the 4th iteration and can be printed at very high speed and still be functional.&nbsp;</p><p>Settings I used:<br>Line Width: 0.6mm<br>Layer Height: 0.28mm<br>Speed: 120mm/s<br>Material:...

Based on a bad experience I had, I have created this protection bar for the Anycubic Photon Mono X Axis. I had an accident where I spilled resin, and it ran down the central axis and jammed the stepper motor. I thought it was damaged because it...

SHOULD WORK WITH ANYCUBIC PHOTON S BUT HAS NOT BEEN TESTED FOR IT! ... INSTALLATION: 1) Unscrew the two screw under the plate mount in the front right corner 2) Insert the spacer between the metal plate and the plate mount 3) Retighten the two...

I made this little adapter so that I could use my Anycubic Photon build plate with the Elegoo Mercury Plus. It is a small quick design that can be quickly printer and used. It is designed to reuse the main bracket hardware that comes with Mercury...

This is the DIY carbon filter for Anycubic Photon Mono SE. It should reduce some resin fumes.The factory carbon filtration of Photon Mono SE doesn't work quite well. Two fans push fumes from build area through the activated carbon sponge to the...

I've printed different drainer for the Photon but no one fits on my Photon Mono 4K. ... So i designed this one.

Full discloser: This filter system was made by  RJ Maker and here is his links, i just made an adapter to fit it on to the anycubic photon: Original files https://www.thingiverse.com/thing:1305485 and his youtube video that explains everything. The...

Simple damper feets for Photon Mono 4K (maybe also fit on a regular PhotonMono)

Wanted a lid to cover the resin vat of a Photon Mono SE.

A knob for the build plate on the Photon Mono X

After installing a chitubox mono LCD screen upgrade for the Anycubix Photon-S and in conjunction with a flexible build plate I found the new addition height of the LCD upgrade would cause the printer homing to fail each print due to Z-home sensor not...

Holder for ANYCUBIC MEGA ZERO BFP TOUCH

All parts print on Anycubic photon. Because of the slight variations in fan sizes some filing of the inside of the fan box parts may be required. I used Gorilla tape just to make sure the fans were sealed since you are venting the exhaust through...

This system extracts fumes from an Anycubic Photon printer without replacing existing panels. Instead, it attaches to the rear of the printer over the top of the rear vents using magnets, preserving warranty validity and ensuring easy attachment and...