anycubic photon ultra 3d models

Based on a bad experience I had, I have created this protection bar for the Anycubic Photon Mono X Axis. I had an accident where I spilled resin, and it ran down the central axis and jammed the stepper motor. I thought it was damaged because it...

*Original Summary* This is my re-creation of the Anycubic Photon MonoX build plate / attachment, the areas I needed anyways. I am going to make some TPU parts for it, so that the resin doesn't get all in the bolt area, crevices, etc. Makes it a...

This is a remix of the other Easy-Bed level mods for the Anycubic Photon printer. The last version broke and deformed after a while, so i designed this version, that is a little bit sturdier and features threaded inserts for the Locking screws.One...

Based on a bad experience I had, I have created this protection bar for the Anycubic Photon Mono X Axis. I had an accident where I spilled resin, and it ran down the central axis and jammed the stepper motor. I thought it was damaged because it...

I tried to install a magflexplate system ( https://www.magflexplate.it/ ) on my Anycubic Photon D2. Problem was the system has an overall hight of 4,5 mm and the printer does not allow to set the zero parameter above the endpoint of the rail. The...

I needed a vent adapter for my new Anycubic Photon Mono X and didn't like the ones already here with the vent pointing straight back so i chose to make my own that's angled to the side. So far there's 4 versions, with differences in screw length and...

There seems to be no hanger for photon mono 2 existing in Thingiverse at the moment, so I created this.

#Description# This is a longer z-stop flag for the Anycubic Photon Mono 4k with the newer version of the build plate arm which has a curved back where it mounts to the z-axis carriage. This z-stop flag is 4mm longer than the original metal piece,...

This is a custom-made adapter designed for using a 92mm fan in place of the rear panel on an Anycubic Photon 3D Printer. The main purpose of this adapter is to install an activated carbon filter element that draws fumes out of the printer through the...

The Anycubic Photon S top cover design is fragile and susceptible to cracking or shattering near the hinge, unlike its predecessor. The top cover should never be allowed to open 180 degrees, which puts excessive strain on the thin plastic frame. My...

Wash machine for Anycubic photon mono. Designed to fit any plastic container you can buy. To adapt to your container, you need to measure its width and depth, and then scale the "bearing_axis_(scalable)_2psc.STL" part according to the measured values...

Simple vat cover for the Anycubic Photo Mono M5s resin printer.

Can be printed on the Photon M3 or any FDM printer. ... First generation, if there are any problems let me know.

8mm and 21mm spacers for 92x25mm and 92x38mm fans. ... I haven't printed these yet myself but you can print them on the Photon by printing it vertically.

I just bought an ANYCUBIC Wash and Cure Station and noticed that the buildplate Adapter is only for the old ANYCUBIC Photon. So I created an adapter fpr the ANYCUBIC Photon Mono. ... Update 01.12.2020 I added a smaller variant for larger prints.

If you are greedy like me you can use this extension to grab any single drop from Anycubic bottle resins ;)

If printing is complete，Use this will save resin Did a nice logo on the file added the .Photon file with supports :) remix from https://www.thingiverse.com/thing:2930511/files

Print the object with no centering ring directly onto the plate and the other with support using a printing service, specifically designed for use on a Photon S device.

Blocks to hold the cover in place! ... if you use an optional seal or not....hold cover in place.. The inspiration comes from my Anycubic Wash&Cure Plus...

Couldn't find a buildplate drain bracket for the Photon Mono SE that can be left on during printing (it seems like the regular Photon buildplate attachment is really close in size but I'm not sure). Holds buildplate at an angle so all the resin drips...

It also helps if your Photon is positioned under a wall cabinet, as it now only needs to be opened halfway (at least with mine). You can use a single one of these parts, which includes STL files for both right and left sides. ...I installed them on both...

Scale it to the Photon M3 Premium VAT dimensions. Split in two parts, for little printers. IMPORTANT: Due to different scaling values, depending on different slicers you have to calculate your own scale factor. ... As an example: I'm using prusa...

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ...The distance from gap to gap on the lid is 15.2 cm.

However, I didn't want to wait and probably planned to upgrade the factory nut anyway, so I designed and printed a temporary nut for the top of my FDM printer first and then printed this one using the Scad program files modified on the photon. This...

standard from the Factory ) i spent almost 4 days with Support and eventually there sending a New Nut - as I didn't want to wait and will probably upgrade the factory nut to something better I designed & printed a temporary nut for the top on my FDM...

i desing this angled cover inspired from @scottyujan desing but his was to big for my 3D Resin Printer so it's a smaller piece that works better for my Photon Zero printer. ... i suggest fliping the 3d model to a 90 degree angle for easier printing...

This is a support for avoid to find a free place for the top cover. ...It simply hang to the printer itself. Printing: PLA, no spécial think. Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/

Remixed from https://www.thingiverse.com/thing:3671334 Specially designed for the latest Photon Zero resin printer, this updated model features smaller components, scaled down by 15% to fit perfectly on the new device. ...Additional stand extenders are...

... you to securely hold a 70mm square active charcoal filter just like this one: https://www.amazon.co.uk/gp/product/B074J8515D. ...Whether you're using an FDM or Resin (Photon) printer, you can easily print this adapter and get started with your project.

This is the holder for a portable heater I use in this video to keep the ambient warm during winter for my Photon. https://youtu.be/sLqAOGNk40s Can be used in other models and other positions, just ignore the plate STL. ... Recommend using PETG or...