anycubic photon s leveling 3d models

... the center of the cover to act as a handle for easier removal. The tolerances are tight, but you can place the cover on the vat and remove it without needing to remove the resin vat from the printer itself. This fits the original anycubic photon.

It allows you to vary the thickness of the spacer.After I tried to install this on my Photon M3 it turns out that the original file can interfere with the linear bearing unless you are very careful. ...I have made changes to limit that potential on both...

This system extracts fumes from an Anycubic Photon printer without replacing existing panels. Instead, it attaches to the rear of the printer over the top of the rear vents using magnets, preserving warranty validity and ensuring easy attachment and...

All parts print effortlessly on Anycubic photon. Due to slight variations in fan sizes, some filing of the inside of the fan box components may be necessary. I used Gorilla tape to ensure fans were securely sealed since exhaust ventilation occurs...

I needed a vent adapter for my new Anycubic Photon Mono X and didn't like the ones already here with the vent pointing straight back so i chose to make my own that's angled to the side. So far there's 4 versions, with differences in screw length and...

Print the object with no centering ring directly onto the plate and the other with support using a printing service, specifically designed for use on a Photon S device.

I just bought an ANYCUBIC Wash and Cure Station and noticed that the buildplate Adapter is only for the old ANYCUBIC Photon. ...So I created an adapter fpr the ANYCUBIC Photon Mono.

**https://www.printables.com/model/643200-anycubic-photon-mono-2-vat-cover** Made a vat cover/lid for the new *Photon Mono 2* since i couldn't find one. Enjoy. There are two models: one titled **VASE** and one titled **RIGID**. The **RIGID**...

Couldn't find a buildplate drain bracket for the Photon Mono SE that can be left on during printing (it seems like the regular Photon buildplate attachment is really close in size but I'm not sure). Holds buildplate at an angle so all the resin drips...

I am creating two versions of my rear vent duct adapters for the Anycubic Photon: a 4" version for connecting to standard ventilation tubing and a 2.5" version for connecting to vacuum hoses and smaller tubing. To install, follow the instructions on...

This is my own try to make the vat for Anycubic Photon Mono X, since I wanted to make a drain stand for the Vat. I dont claim that it is totally exact as the original but as close as possible I could make it. If anyone finds anything wrong with it...

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

An Anycubic Photon vat holder is designed specifically to drain resin back into the bottle. The center of the vat should sit directly in the middle of a 1-liter bottle, with the bottle pushed up against the Skadis pegboard. A unique attachment on the...

I know, there are some vent systems for the Anycubic Photon already available but I didn't find one that includes a rear fan, which is why I designed this one. ... What you need: * 1 - 92x92x14 mm fan (Noctua NF-A9x14) * 4 - M3 x 16mm socket head cap...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

This is a z limit spacer for the Anycubic Photon Zero. It allows you to raise the height at which your z limit triggers for the Wham Bam FBS bed. This replaces the current metal bracket that blocks the sensor. The only difference between this and...

I wanted to give it a more personalized feel to this cover so I added the Photon and the Anycubic logo to it. Please notice that the area where the big logo is located is very thin and some might assume is not full uv-proof. I am fine with mine....

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

This accessory, designed to replace the upper glass of the Anycubic photon printer, will draw in part of the odor emitted by the resin during printing and, with a rubber tube properly connected, discharge it outside. For example, allowing the tube to...

Crafted specifically for Anycubic Photon printers, this platform accommodates the resin tanks seamlessly. Once printing is complete, simply slide the tank into place, shielding the lower area from splashes, scratches, and dust. This way, you can...

Wash machine for Anycubic photon mono. Designed to fit any plastic container you can buy. To adapt to your container, you need to measure its width and depth, and then scale the "bearing_axis_(scalable)_2psc.STL" part according to the measured values...

This is a custom-made adapter designed for using a 92mm fan in place of the rear panel on an Anycubic Photon 3D Printer. The main purpose of this adapter is to install an activated carbon filter element that draws fumes out of the printer through the...

i desing this angled cover inspired from @scottyujan desing but his was to big for my 3D Resin Printer so it's a smaller piece that works better for my Photon Zero printer. ... i suggest fliping the 3d model to a 90 degree angle for easier printing...

Rear bulkhead of the Anycubic photon is a crucial component that requires precise installation. Two versions are available, one identical to the original and another adapted specifically for the ethernet connector. Key steps include preparing the...

Based on a bad experience I had, I have created this protection bar for the Anycubic Photon Mono X Axis. I had an accident where I spilled resin, and it ran down the central axis and jammed the stepper motor. I thought it was damaged because it...

This device is designed to be attached to the Anycubic Photon, specifically aimed at reducing the smell from resin use.\r\nA brushless fan with an 80mm diameter should be installed between the panel and the box, secured in place using m5...

FEP-Ersatzrahmen für einen Anycubic Photon Zero. Der Originale ist geklebt, so das ein Austausch nicht so einfach ist. ...Ich habe den Rahmen von bsweeney930 heruntergeladen und dann soweit modifziert das der FEP-Film besser gehalten wird.</p> <p>Am...

This is designed for straining and collecting debris from anycubic photon vat systems. It can be particularly frustrating to go through the straining process after encountering failed prints, especially when the hardened resin is not visible at all...

I made this little adapter so that I could use my Anycubic Photon build plate with the Elegoo Mercury Plus. It is a small quick design that can be quickly printer and used. It is designed to reuse the main bracket hardware that comes with Mercury...

@DocTanner crafted an innovative Rear Vent duct adapter for the Anycubic Photon, available here: https://www.myminifactory.com/object/3d-print-64661. I sought to enhance this design by adding a feature that would allow me to incorporate filters...