anycubic photon s filter 3d models

Adapter for Photon Mono buildplate to mount on Anycubic Wash & Cure Station. Uses M6 screws, like the original. I used a height of 15mm instead of 12mm of the original mount on the Photon Mono. It makes everything a bit more stable and for me...

**https://www.printables.com/model/643200-anycubic-photon-mono-2-vat-cover** Made a vat cover/lid for the new *Photon Mono 2* since i couldn't find one. Enjoy. There are two models: one titled **VASE** and one titled **RIGID**. The **RIGID**...

Another version of the great “ANYCUBIC PHOTON Easy Leveler” by wundel https://www.thingiverse.com/thing:3096818. In this review, only two improvements are notable - pressure springs have been included to avoid holding the plate in place with your...

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

Crafted specifically for Anycubic Photon printers, this platform accommodates the resin tanks seamlessly. Once printing is complete, simply slide the tank into place, shielding the lower area from splashes, scratches, and dust. This way, you can...

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

This accessory, designed to replace the upper glass of the Anycubic photon printer, will draw in part of the odor emitted by the resin during printing and, with a rubber tube properly connected, discharge it outside. For example, allowing the tube to...

This is my own try to make the vat for Anycubic Photon Mono X, since I wanted to make a drain stand for the Vat. I dont claim that it is totally exact as the original but as close as possible I could make it. If anyone finds anything wrong with it...

I am creating two versions of my rear vent duct adapters for the Anycubic Photon: a 4" version for connecting to standard ventilation tubing and a 2.5" version for connecting to vacuum hoses and smaller tubing. To install, follow the instructions on...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

An Anycubic Photon vat holder is designed specifically to drain resin back into the bottle. The center of the vat should sit directly in the middle of a 1-liter bottle, with the bottle pushed up against the Skadis pegboard. A unique attachment on the...

This is a z limit spacer for the Anycubic Photon Zero. It allows you to raise the height at which your z limit triggers for the Wham Bam FBS bed. This replaces the current metal bracket that blocks the sensor. The only difference between this and...

I wanted to give it a more personalized feel to this cover so I added the Photon and the Anycubic logo to it. Please notice that the area where the big logo is located is very thin and some might assume is not full uv-proof. I am fine with mine....

I know, there are some vent systems for the Anycubic Photon already available but I didn't find one that includes a rear fan, which is why I designed this one. ... What you need: * 1 - 92x92x14 mm fan (Noctua NF-A9x14) * 4 - M3 x 16mm socket head cap...

Wash machine for Anycubic photon mono. Designed to fit any plastic container you can buy. To adapt to your container, you need to measure its width and depth, and then scale the "bearing_axis_(scalable)_2psc.STL" part according to the measured values...

#Description# This is a longer z-stop flag for the Anycubic Photon Mono 4k with the newer version of the build plate arm which has a curved back where it mounts to the z-axis carriage. This z-stop flag is 4mm longer than the original metal piece,...

I installed a HEPA air filter on my Anycubic Predator, utilizing a CarstenD enclosure that retains all original components. ...To achieve this, I fabricated a duct from an existing opening in the printer's casing.

The factory Photon Mono SE advertises a "carbon filtration" system, but in reality it just consists of two really small fans (30mm x 30mm, similar size to the ones for cooling Raspberry Pi's) that pull air from the build area, through some activated...

i desing this angled cover inspired from @scottyujan desing but his was to big for my 3D Resin Printer so it's a smaller piece that works better for my Photon Zero printer. ... i suggest fliping the 3d model to a 90 degree angle for easier printing...

Rear bulkhead of the Anycubic photon is a crucial component that requires precise installation. Two versions are available, one identical to the original and another adapted specifically for the ethernet connector. Key steps include preparing the...

Based on a bad experience I had, I have created this protection bar for the Anycubic Photon Mono X Axis. I had an accident where I spilled resin, and it ran down the central axis and jammed the stepper motor. I thought it was damaged because it...

This is designed for straining and collecting debris from anycubic photon vat systems. It can be particularly frustrating to go through the straining process after encountering failed prints, especially when the hardened resin is not visible at all...

FEP-Ersatzrahmen für einen Anycubic Photon Zero. Der Originale ist geklebt, so das ein Austausch nicht so einfach ist. ...Ich habe den Rahmen von bsweeney930 heruntergeladen und dann soweit modifziert das der FEP-Film besser gehalten wird.</p> <p>Am...

I made this little adapter so that I could use my Anycubic Photon build plate with the Elegoo Mercury Plus. It is a small quick design that can be quickly printer and used. It is designed to reuse the main bracket hardware that comes with Mercury...

However, I didn't want to wait and probably planned to upgrade the factory nut anyway, so I designed and printed a temporary nut for the top of my FDM printer first and then printed this one using the Scad program files modified on the photon. This...

Simple angled Photon Mono Build Plate holder. ...Heavily inspired by this design for the Photon Zero: https://www.thingiverse.com/thing:4224960 Modeled in TinkerCAD.

I've printed different drainer for the Photon but no one fits on my Photon Mono 4K. ... So i designed this one.

... I used for the Thingiverse Files I used : - http://www.thingiverse.com/thing:3419926 Thanks to Corona688 Enjoy Parts Needed I just removed two of the original M3 screws and replaced them with longer ones. P.s Check out my Other Photon Mods

Simple damper feets for Photon Mono 4K (maybe also fit on a regular PhotonMono)

A knob for the build plate on the Photon Mono X