anycubic photon print sticking to fep 3d models

There are dedicated spots for a 3x10mm magnet, available at home improvement stores like Home Depot or Lowe's, to assist in keeping the lower part of the kickstand securely in place. ...Fortunately, during my testing phase, these magnets were not...

... The upper portion is a remix of The_Monstro's work, which can be found on their profile here: https://www.thingiverse.com/The_Monstro/about To assemble this design: - Utilize 8 countersink original screws from Photon to secure the platform and bed.

Using this bracket after completion of printing allows for additional resin to be dropped easily. Secure attachment of bolts and knobs with M6 or 1/4-20UNC threads ensures a stable connection to the bracket. ...A tap is necessary to create precise M6 or...

... least 2.5mm. Do not use Support. Do not use any raft or brim. Use a layer height of .25 mm ) 3. Print the pattern part first and afterwards the other without removing the already printed. 4. ...Detach the old screen skin and apply your new.

... forcing hinges and risk scratching the paint. ...This is a straightforward door stopper printed on TPU filament (smart materials FLEX). I employed a slim 3M double-sided adhesive to secure it to the frame. ...Not visually appealing, yet functional.

Note To Users: The model depicted is an early version where the central cylinder extends too far, causing it to touch the bottle's opening. ...However, the uploaded STL file represents version 2, which has been modified to reduce the extrusion length...

Disclaimer 1: I am not sure whether the last drops are clean enough to be used for printing. Disclaimer 2: Make sure to put the VAT on a clean surface during the process. Disclaimer 3: The depicted version is the initial where the extruded middle...

This handy device allows you to securely hold a resin bottle while pouring its contents into the vat, eliminating the frustration of watching it drip away. Simply press-fit the ring component onto the post supporting the build plate and position the...

... a simple solution. You can always give the tights mesh a good wash with some rubbing alcohol and reuse them multiple times. Hope you find this helpful! Happy printing! Update 1: You can use rubber bands to hold the filter in place on the sides.

Help is needed to drain the ink from the printer to save on resin costs.

This filter tower can be easily attached to the interior fan without any change. Add an active carbon filter. ...I recommend to remove the filter below the fan.

Extension for the homing bar to allow for a magnetic base.

To be honest, my printer's lid kept falling off whenever I opened it due to its tendency to swing all the way back. So, I decided to create a wedge that would prevent this from happening in the first place. ... All it takes is some double-sided tape...

I'm installing a ventilation system to clear out the stinky air from my space. ...The tube is connected to an exhaust hose that leads directly outside, drawing fresh air in and pushing stale odors out.

... attractive holder for the spatula - that's what I aimed to design. I included a dummy spatula model as my reference point, in case someone needs to double-check or verify something. ...It could even prove useful as a spare spatula, who knows?

... new lid. There are two options available: a full cover version and an "easy" version featuring two cut-outs that allow you to place the lid on the vat without loosening any screws. ...Both versions fit perfectly on vats with either type of spout.

This is a guide for the build plate to properly square before locking it tight during Z calibration. Not all machine are the same set up, Guide may need some length adjustment. ...Please do modify if needed.

... nice looking holder for the spatula, that's it. i added a dummy spatula model i used as my reference just in case some one needs to double check or anything... ...it may even be usefull as a spare spatula (?) Category: 3D Printer Accessories

With these shields in place, I'm confident that I can safely leave the resin inside the printer for an extended period without worrying about exposure to light. ...The 16 magnets I've employed have a 18mm diameter and 5mm height, but interestingly, the...

An old nylon stocking is employed to prevent dust particles from falling into the resin. The transparent tube measures 110 mm in length, equipped with a re-used fan operating at 24 volts. ...This setup works flawlessly, eliminating the still intense...

Durch dieses Zwischenstück wird der Zero-Sensor etwas früher erreicht, es gehen aber ca 5mm an Bauhöhe verloren.I created this spacer after I mounted my flexible buildplate and had problems to adjust the zero point. ...With this spacer, the zero sensor...

The original idea came from Doc Tanner at https://www.thingiverse.com/thing:2877754 if you want to checkout his. He's much better at CAD than I am. I created this using Tinkercad...and it shows. This design uses a standard 12v 80mm case fan and...

Z Limit Spacer for Anycubic Photon M3 Max to use with a Wham Bam FBSR. I have created 2 spacers for the Anycubic Photon M3 Max, one for use with Wham Bam’s regular Flexible Build System at 2.6mm tall and the other at 3.8mms tall for use with their...

I have created a spacers for the Anycubic Photon Mono X,for use with Wham Bam XTR line Flexible Build System at 3.8 mm tall You just need to print in resin or FDM and unscrew the interceptor arm from the machine and put the spacer between the build...

Replacement frame for attaching FEP to Photon Mono 4k bathtub. The original is non-reusable consumable so this design successfully meets the reusability option with any other brand FEP including. Same screws are used. For best tensioning tighten...

Printed with six perimeters and six top and bottom solid layers at 20% infill to ensure strong solid shells either vertically or horizontally. Update: I've added version two of the bracket, which is more compact and uses less material while still...

Adapter to be able to hang a Anycubic Photon build plate to the build plate bracket of the Elegoo Mercury Plus wash and cure machine. **Before printing, ensure the material you're going to print it in is compatible with the cleaning solvent you're...

The Mounting Tool is a device specifically designed to securely attach the FEP film onto any desired surface. ... Printed with PLA at a layer thickness of 0.2mm using the reliable Anycubic Chiron printer.

Anycubic Photon Mono drain bracket

Anycubic Photon S Drip Hanger