anycubic photon print sticking to fep 3d models

Model of Anycubic Photon Mono X SLA 3D Printer Resin VAT

Used Blender CAD Sketchup with drivers to generate an updated version of drip hanger for AnyCubic Photon Mono X 6k that can be left in place while printing.  Hangs build plate off to one side, so may need a drip plate into vat depending on print. ... I...

This is a bluild plate drain for Anycubic Photon M3 that i designed. I printed it in my fdm printer in 0,2 layer higth whit support for the slot. ... Its inclined at 40°.

Couple brackets for the Anycubic Photon Mono X's power supply. Print 2. Install screw through bracket, there's a hole for a screwdriver. Recommend scaling up maybe 2-3% because I made it too tight. ...Screws are #6.

This is a z limit spacer for the Anycubic Photon D2 DLP. It allows you to effectively raise the height at which your z limit triggers.I have included two sizes, 2mm and 2.5mm. I used the 2mm spacer on my Photon D2 with a WhamBam flexible build plate....

This is a z limit spacer for the Anycubic Photon. It allows you to effectively raise the height at which your z limit triggers. There are 2 files here. I used the 2mm spacer on my photon with a WhamBam flex plate and it has been perfect. I later...

This is designed for a window guide width of 1.1inch see picture and a 3inch exhaust duct.  These parts are designed to be printed on the Anycubic Photon printer.  I suggest printing with ABS resin.  Additionally the parts are designed to be a...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be 10 of them. The ridges are 0.25mm wide and 0.5mm apart. For each one missing, you are losing 0.25 to 0.50mm of LCD pixels from...

If you want to use a magnetic flexible plate on the Anycubic Photon M3 you need to put a spacer on the z-axis end stop sensor bracket to compensate for the thickness of the magnet an plate.

This new base is designed to replace the bottom plate on the Photon S and vents both the bottom and back vents through a 4" collared opening meant for connection to a 4" flexible vent, which can be hooked up to an inline fan and then into a filter or...

This is an activated carbon sachet holder to fit internally into a Anycubic Photon. This forces internal MEK vapors to be drawn through activated carbon before exhausting, reducing odor significantly. ... 2 pieces.

2.5mm z-axis separator for the anycubic photon mono 4k. ... The distance from the center of one circumference to the other is 8.5mm, the circumferences are 3.5mm Required if a flexible platform is to be used

Riser for the Anycubic Photon M3 lid to allow passage of a small power cord in the back left corner. Useful for things like heaters, air cleaners, etc. Print the single piece if you have a big enough printer. It has also been split into four...

This bracket mounts the power supply brick for an Anycubic Photon S to the side of a desk Interior dimension are 2.0 inch wide by 1.3 inch deep by 4.26 long.

A lid, printable on a Mk3s or similar, to keep the resin smells in the resin tank of an Anycubic Photon Mono X contained. Convenient handle. ...No need for supports.</p>

This box with a Nikon logo lid holds several SD and CF cards in place side by side.\r\nUpon printing the original design on my photon, I encountered issues - the lid and the box did not fit together properly, the CF section was too small for my CF...

This replaced the carbon container from the Photon-SIT can, which can easily be screwed down due to the shafts, so that the carbon can be filled before installation. For reference, check out the Anycubic Photon-S Carbon insert-container V6 for more...

Remixed versions of a photonsters backplate for the Anycubic Photon that allows you to install a [CAT.6 Inline Coupler](https://www.amazon.de/VCE-Ethernet-Patchkabel-Verbinder-Verlängerung-CAT6/dp/B07Q345W78) 16x18x30.7mm Ethernet jack. ... Ethernet...

This is a Remix of Skody01's [Anycubic Photon M3 build plate drain](https://www.thingiverse.com/thing:5674605). I modified the inclined holder to also incorporate a slight angle (7.5°) towards the back, so that the resin flows towards only the left...

Hot news (from comment): Anycubic 4K new firmware at their website, and included their RERF file, so my design should work still fine but time step changed After few days searching RERF file for my brand new Anycubic Photon Mono 4K, i found nothing...

... This ensures compatibility and optimal performance. Additional Resources For detailed instructions and troubleshooting guides specific to your Anycubic Photon model, refer to the official user manual or visit the manufacturer's support website.

Looking for a quality drip hook mount for your Anycubic Photon Mono 4K? ...Look no further than my remix of Anycubic Photon Mono 4K drip hook mount! Short video:https://youtube.com/shorts/24oSgpB7lEA?feature=share

Air vent system for Anycubic Photon Mono M5s Absaugsystem für den Anycubic Photon Mono M5s Gedacht für ein 50mm Abluftschlauch und einen 80x80mm Lüfter Kann größtenteils ohne Support gedruckt werden. Teile werden geklebt, dafür sind die Verbinder...

Damper Feets for Anycubic Photon Mono 4K --------------------- Simple damper feets for PhotonMono 4K (maybe also fit on a regular PhotonMono)

This mounting bracket secures the power supply brick of an Anycubic Photon S on the side of a desk.

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

**https://www.printables.com/model/643200-anycubic-photon-mono-2-vat-cover** Made a vat cover/lid for the new *Photon Mono 2* since i couldn't find one. Enjoy. There are two models: one titled **VASE** and one titled **RIGID**. The **RIGID**...

Adapter for Photon Mono buildplate to mount on Anycubic Wash & Cure Station. Uses M6 screws, like the original. I used a height of 15mm instead of 12mm of the original mount on the Photon Mono. It makes everything a bit more stable and for me...

Another Version of the Genius “ANYCUBIC PHOTON Easy Leveler” by Wundel https://www.thingiverse.com/thing:3096818 In this Review, Only Two Improvements Are Made - Pressure Springs and Insert Positioning The only improvements made to this design are...

Viewer for Anycubic Photon print files and settings. Timing setting can be easily modified. ... Updated to Version 1.1: - View layer images, storing each image as a png file - Display resin consumption in milliliters Updated to Version 1.2: - Drag and...