anycubic photon mono x vat 3d models

This is a proposal to increase the Z-stroke of the mono X photon printer. The first modification is to the Z-stroke detection system. Simply replace the original part with the part named "Z stroke end detection screw holder" and add a screw that...

Some resin printers come with something like this, the Photon Mono X does not, so I designed my own. I designed it to be press fit on the machine so it would be snug and not shift/move, if it comes out too tight you may need to sand it a little to...

This is an OpenSCAD version of the original Anycubic Mono X Wham Bam Z axis spacer by Elantris. ...It allows you to vary the thickness of the shim.

I love my anycubic Mono X but I was finding it challenging to find a place to set the lid between prints and maintenance. I also found I was getting little splotches on the plastic from my gloves - even with the added side handles. This solution...

It works with mono x.Top and bottom are the components of the tank. Print both and glue together with resin and cure with UV.The cap is scaled down of 0.05 to better fit without applying force.Be careful to remove the tank from vat as the resin will...

This is a basic handle for the Anycubic Mono X. Use 3M double sided tape to adhere to the lid. Sand the bottom of the printed handle for better adhesion. I used 3M auto adhesive tape. ...

This is a basic handle for the Anycubic Mono X. Use 3M double sided tape to adhere to the lid. Sand the bottom of the printed handle for better adhesion. ... I used 3M auto adhesive tape.

This is a redesign of the cover for Mono X printer that allows you to have good access to the printer even in tight spaces and without completely removing the cover every time. The cover consists of two parts of which the back is fixed to the printer...

Since i find very tedious to remove the lid from the Photon I build a counterweight system so It's easy to lift and is out of the way while working on the printer. The pulleys are made from 2 wheels sandwiched together reclaimed from another 3d...

This is an OpenSCAD version of the original Anycubic Mono X Wham Bam Z axis spacer by Elantris. ...It allows you to vary the thickness of the shim.</p><p>The original model can be found here: <a...

These allow you to use "Workhorse Safety NIOSH P100" filters (The adapter seems a little different from the 3M adapter.) to assist in cleaning air for the Anycubic Photon Mono X. It all does limit the airflow, but ideally improves the air quality. ...

If you use a flexible steel plate flex bed on the Photon X 6K, then you cannot calibrate the Z-Axis anymore, because the new flex bed sticker adds 2.7mm to the bed. This new flag will compensate for that. This flag is to adjust the z limit switch...

Here is the extractor/ventilator I have made for the Anycubic MONO X. I wanted a design that wouldn't invalidate any warranties by messing with panels and internal fans or cutting into the nice cover, that could ventilate the build chamber after...

https://www.thingiverse.com/thing:4765628) A simple but effective way to prevent those few drops from reaching just outside the vat when you put something on the dripping holder and to shove the build plate and the dripping rack back onto the arm. I...

... ... https://www.thingiverse.com/thing:4765628) A simple but effective way to prevent those few drops from reaching just outside the vat when you put something on the dripping holder and to shove the build plate and the dripping rack back onto the arm.

Resin drainer for anycubic Photon Mono 4K 3D printer.

These are two covers for the two top and bottom sides, (the one to protect from dust, light and to avoid odors, the other to protect the sheet)

Don't you just hate it when during manipulation of the build plate a resin drop lands on the outer edge of the vat, finding its way between FEP and glass ?This design adds a large rim around the front of the vat.Two versions are available, the full...

Hello there, this is a support to let you to drain your resin bottle in to the VAT. It could be used with plate installed or not, and also with different size of resin. I think is very useful and in different situations. ...

Hello there, this is a support to let you to drain your resin bottle in to the VAT. It could be used with plate installed or not, and also with different size of resin. I think is very useful and in different situations. Print Settings Printer:...

This remix include: -prolonging the hanger to better support printing bed - it should stop rotating around the screw - it was 2 mm short in my printer -adding cut off so the screw lay flat on bed (earlier it was partially on hanger partially on bed)...

... on Thingiverse. Click this link to become part of the Photon Army: https://www.thingiverse.com/groups/anycubic-photon Watch this video for step-by-step instructions on how to clean your resin vat after printing: https://youtu.be/-9aPhhMv4ww

This is an air purifier for the inside of a Photon Mono X(Photon mono X 6K) 3D printer It needs two fans with dimensions of 6 * 6 * 1.5 cm 12 V And some activated carbon for its 10 cm tank Requires a 12 volt adapter Purifies up to 95% of resin odor...

Кронштейн для слива смолы с детали и стола после завершения печати. ...Наклоняет стол на 30 градусов, что позволяет стечь остаткам смолы

Les possesseurs d'Anycubic Photon Mono 6k seront peut-être intéressés par la modélisation d'un couvercle et d'une base pour leur bac à résine (VAT). Modélisation réalisée avec Freecad. Le couvercle s'imprime sur le plateau d'une Prusa MK3S, la base...

I designed it specifically for my vat, which is used with both the Elegoo Mars and the Anycubic Photon, but added an inner lip to prevent the FEP from touching the bottom. ...This setup means that the FEP might sag slightly, since it's completely...

I upgraded my Anycubic Photon Mono SE with Solvo magnetic buildplate. ...So i needed this spacer to save my screen from crashing.

Les possesseurs d'Anycubic Photon Mono 6k seront peut-être intéressés par la modélisation d'un couvercle et d'une base pour leur bac à résine (VAT).Modélisation réalisée avec Freecad.Le couvercle s'imprime sur le plateau d'une Prusa MK3S, la base est...

... can drip dry. ...Faces the bottom of the plate forward so you can remove the part from the plate while it's hanging. Designed for Anycubic Photon Mono but will fit any printer with a similar build plate arm size. ...Build plate arm size is 2" x 0.5".

This is a spacer that can be used on the Anycubic Photon Mono to move the z limit trigger down 2.6mm. Alternately you can use 2 small washers. ...