anycubic photon mono x power supply 3d models

Adapter for Photon Mono buildplate to mount on Anycubic Wash & Cure Station. Uses M6 screws, like the original. I used a height of 15mm instead of 12mm of the original mount on the Photon Mono. It makes everything a bit more stable and for me...

**https://www.printables.com/model/643200-anycubic-photon-mono-2-vat-cover** Made a vat cover/lid for the new *Photon Mono 2* since i couldn't find one. Enjoy. There are two models: one titled **VASE** and one titled **RIGID**. The **RIGID**...

This is the DIY carbon filter for Anycubic Photon Mono SE. It should reduce some resin fumes.The factory carbon filtration of Photon Mono SE doesn't work quite well. Two fans push fumes from build area through the activated carbon sponge to the...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

Wash machine for Anycubic photon mono. Designed to fit any plastic container you can buy. To adapt to your container, you need to measure its width and depth, and then scale the "bearing_axis_(scalable)_2psc.STL" part according to the measured values...

Hi!I made this for my Anycubic Photon Mono SE. This is the 4th iteration and can be printed at very high speed and still be functional. Settings I used:Line Width: 0.6mmLayer Height: 0.28mmSpeed: 120mm/sMaterial: PLASupports: No!You can use...

This is the DIY carbon filter for Anycubic Photon Mono SE. It should reduce some resin fumes.The factory carbon filtration of Photon Mono SE doesn't work quite well. Two fans push fumes from build area through the activated carbon sponge to the...

German: Resin Tank Halter für den Anycubic Poton mono 4k. Es gibt zwei Versionen des Auslegers, der Halter passt nur auf die im Bild oben gezeigte Version. Der Halter kann liegend, mit Support an dem Langloch oder stehend gedruckt werden. Resin...

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ... The distance from gap to gap on the lid is 15.2 cm.

This is a support for avoid to find a free place for the top cover. ...It simply hang to the printer itself. Printing: PLA, no spécial think. Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ...The distance from gap to gap on the lid is 15.2 cm.

The factory Photon Mono SE advertises a "carbon filtration" system, but in reality it just consists of two really small fans (30mm x 30mm, similar size to the ones for cooling Raspberry Pi's) that pull air from the build area, through some activated...

Couldn't find a buildplate drain bracket for the Photon Mono SE that can be left on during printing (it seems like the regular Photon buildplate attachment is really close in size but I'm not sure). Holds buildplate at an angle so all the resin drips...

It simply hang to the printer itself.Printing: PLA, no spécial think.Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/Print...

This lid also WORKS with Photon Mono -V3 fix overall fit (needs a well-tuned printer so print fits properly) -V2 fix corners and other small details -Add no logo version This resin vat lid keeps dust and other debris out of your resin tank and also...

#Description# This is a longer z-stop flag for the Anycubic Photon Mono 4k with the newer version of the build plate arm which has a curved back where it mounts to the z-axis carriage. This z-stop flag is 4mm longer than the original metal piece,...

One of the things I miss about the original photon was how easy you could rotate the bed by 90 degrees after printing to allow hollow parts to drain fully, this design achieves the same thing but at a angle of 88 degrees to keep the top of the build...

I've seen several Photon Mono adapters for Wash & Cure, but I didn't feel like twisting and unscrewing the mount every time, and I also wanted to use the metal bracket that came with the kit rather than throw it away. The difference with my adapter...

This lid ONLY WORKS with the Metal photon mono vat. Stock plastic vat will not work.</p><p>-V3 fix overall fit (needs a well-tuned printer so print fits properly)</p><p>-V2 fix corners and other small details</p><p>-Add no logo version</p><p>This...

I've seen several Photon Mono adapters for Wash &amp; Cure, but I didn't feel like twisting and unscrewing the mount every time, and I also wanted to use the metal bracket that came with the kit rather than throw it away. The difference with my...

Made a vat cover/lid for the new Photon Mono 2 since i couldn't find one. Enjoy.There are two models: one titled VASE and one titled RIGID.The RIGID model is a thicker, more robust version. The two cylinders are knob covers and need to be glued on...

You can use NFEP or ACF films with this frame avoiding those trash anycubic original feps wih frame. You need to thread the 3mm holes with a 3mm tap drill. I used M3 x 0,5. Also you can use 1/8" thread. ...Thread the Male Frame Materials: PETG...

I liked the vat drip holder from this maker friend https://www.thingiverse.com/thing:3671334 but didn't have the best size depth for my mono x2 vat So I remixed this stand to it, with best size for mono X2 vat depth including a small cut extrude...

If you are greedy like me you can use this extension to grab any single drop from Anycubic bottle resins ;)

simple remix to Daniels build to fit the new version of the mono 4k since they made some changes to the gantry and now has different dimensions. ...This is for the model of printer that has black metal gantry made from folded/molded gantry.

simple remix to Daniels build to fit the new version of the mono 4k since they made some changes to the gantry and now has different dimensions. ...This is for the model of printer that has black metal gantry made from folded/molded gantry.

Resin vat cover for the Mono 2Helps keep odor down when not printingPreserves resin from environment (stray UV!)Helps prevent spillages if moving the printer with resin in the tankPrinted on a Creality Ender 3 S1 Pro in Sunlu PLA Meta.

... this thing: https://www.thingiverse.com/thing:5442710 (the "anyc_csonk.stl") You can connect a flexible 100mm flexible pvc pipe to it. You need a bigger printer for this project: 273mm x 223mm. ... On the photos you see my first try without

Photon mono x gap cover with filter.