anycubic photon mono x power supply 3d models

Anycubic "Photon Mono 4K" resin vat bottom frame for FEP film. The dimensions fit the standart Photon mono 4k resin vat and standart FEP film. The model was made to replace the factory disposable plastic frame with an improved reusable aluminum...

New Power Supply Cover for Anycubic I3 Mega Fans from 40mm to 60mm and 100mm, Height Up to 25mm. The White Area in the Picture is from Glue. I Recommend v3 with the 100mm Fan. It's the Slimmest Version and Needs Only One Fan. v1: Old Design for Two...

Anycubic Photon Backplate With Switch and Power for Heater. This backplate is new, with cutouts designed specifically for a switch and barrel jacks to power a PTC heater. One version also includes a cutout for an Ethernet jack. ...For further...

Replace the FEP film for Anycubic Photon Mono (6.08 inch 2K), after modification, everything is normal and the cost is low. Preparation: Tools: 1. Electric drill 2. Screwdriver 3. M3 drill bit 4. Scissors 5. Wire cutter Material: ...

The [Mainboard FAN] blows air directly into the Power Supply, which prevents compressed air from escaping through the Switch and ensures that fresh air flows freely out of the Power Supply FAN area. This is crucial for maintaining optimal airflow and...

Unfortunately, changing the power supply also meant the fastening screws are now M4 instead of M3, so I created a remix of the adapter to accommodate the change and used these M4 screws from https://www.amazon.de/dp/B07FB53L5L to secure the power...

I built the PTC heater for my Mono but I needed a clean way to run the wires out to the power supply. This is a minimal riser that has a 1" gap in the back to allow wires to pass through. You can improve the seal by adding foam, batting, hot glue,...

This is a z stop extension plate for the new version of the Anycubic Photon Mono 4K 2022 version. There is no place to put a spacer on the new printer, so you must print an extension when installing a magnetic bed plate for homing purposes. I printed...

Next, install the fasteners and place the power supply on top. The front cover is printed separately and attached to the rails. If desired, it can be adhered using adhesive. The contact area with the switch is mounted independently in any location....

Set the right amount of slack on your Anycubic Mono X, Mono X 6K, and/or M3 Plus FEP with this spacer puck. It was designed with measurements taken from an OEM FEP installation, so achieving proper tension/tuning should be fairly easy. Three files...

Here are my other designs for the Anycubic Mono X 4K ANYCUBIC Photon Mono X Clip On Heater Mount http://www.thingiverse.com/thing:5190198 ANYCUBIC Photon Mono X Z-Axis Bumper Guard http://www.thingiverse.com/thing:5185340 Anycubic Mono X Lid Spacer...

This is a basic protective covering for a power source unit.

Can be printed in one run on the Anycubic Kobra and requires no additional parts to function. Tested with the original screws and the additional cover. It might even work with a 60x25mm fan but I only tested with a 60x15mm one. If you are...

Drip bracket for Anycubic Mono M5s Because of the very aggressive drip angle, if your print is too big, might not fit on the bracket. ...

Please use the attached ZIP Files. ...The STL is only a place holder to upload the .ZIP File . Created from my original Stick delivered with my Anycubic Mono

The device for the printing platform of the 3-D printer Anycubic Photon Mono 2After printing, a large amount of photopolymer resin may remain on the part. To help the resin drain from the part, I developed this device.It is installed in place of the...

The Anycubic Photon Mono requires a z stop spacer to accommodate the thickness of the Wham Bam Flexible Build System. I created a spacer that goes between the z axis carriage and z stop metal tab that triggers the sensor to stop. The original...

Mount a Power Connector to the Base with Two Additional Outlets. The outlets are designed to connect hotend harnesses, which include heaters, sensors, and four extra wires for Z-sensor functionality. Additionally, they accommodate extruder stepper...

Wham Bam's magnetic flex plate is awesome but adds 2.6mm to the height of the build plate. Unfortunately, there isn't enough play in the build plate mount so the Z stepper grinds when I home the plate. One option is to print a 2.6mm spacer but I...

I didn't want to wait on a Wham Bam plate because I had prints that needed to get done so I ordered the Sovol plates from Amazon. They had a slightly different height recommendation (2.7mm) so I remixed this adapter in Tinkercad. ...Not only were they...

This is a R_E_R_F test file for the Anycubic Photon Mono. All the ones I found out there took a while to run, so in the interest of saving time and resin, I created a R_E_R_F file that is heavily inspired by the ResinXP2-ValidationMatrix_200701...

This is a R_E_R_F test file for the Anycubic Photon Mono. All the ones I found out there took a while to run, so in the interest of saving time and resin, I created a R_E_R_F file that is heavily inspired by the ResinXP2-ValidationMatrix_200701, but...

... made by goyetus. ... It uses: 3 x m3 Nuts. 3 x m3 x 12 16 Magnet 5x5x5 Changed the back plate to use this fan: https://es.aliexpress.com/item/32810655513.html?channel=twinner Added the step file to modify the back as you want.

By downloading User also acknowledges and understands the above and agrees to hold the creator harmless from any and all liability I printed in PETG and here are my settings: Machine: Ender Extender 400x400x500 Nozzle: 0.6 Layer height: 0.48 Line...

I wanted to get a magnetic build plate for my Photon Mono M5, but WhamBam only had it for the M5S. After a bit of research, and determining that the build plates are the same size, I decided to give it a try, and it seems to work perfectly with this...

Customized version of https://www.thingiverse.com/thing:3911914 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3911914

Thanks to @SnopSnapi for the excellent model and sharing the CAD.  I was  able to import and quickly add some countersunk holes for M3 fasteners to hold the lid more securely.I attached with M3x10 SHCS and M3 Locknuts on the inside of the lid/cover...

I made this to help remove more resin from my prints. It seams there is still so much resin on the models after printing even though it has been hanging upside down for a while. This clamp holds the platform at a 90 degree angle from the vat. This...

These feet will fit perfectly in the oval recess of the printer. Print them in TPU and it will keep the printer from sliding so easily and reduce some vibration. Use you Z axis scaling to print them as tall as you like. For example, My printer was...

Part to be installed after printing to tilt the tray to drain the resin more easily. A modification compared to the photo because the screw did not pass. ... An M6 nut and an M6x30 screw to fix the tray if needed.