anycubic photon mono x leveling 3d models

Since the standard models don't deliver for me, I opted to explore an alternative method of leveling the bed, drawing inspiration from the Kelant S400's concept but avoiding any drastic modifications to my printer. Apologies for the larger part file...

“Flexible Spring Steel Resin Build Plate 224x129mm” Amazon link: https://www.amazon.com/dp/B0C2C3DJRB This magnetic build plate is slightly larger, or 1mm larger in width and depth, I think the original build plate is at this dimension: 218 x 123 x...

Official Anycubic Photon Mono SE official R_E_R_F.pwms file for those that never received a copy

Photon Mono Vat Cover. ... Designed with Fusion 360

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

... that has caught their attention - the Funnel. ...This small but mighty device makes it super easy to handle resin and other liquids, allowing users to achieve perfect flow control every time they use it with their beloved Anycubic Photon printer.

Spacer with cable hole for the Photon Mono inspired by ferro5's spacer for the Mono X. In case you want to put a heat source into the housing to keep the resin at nice 20-25° your cable will get into way. The spacer lifts the lid a bit and...

Replaces Photon Mono frame. ... Best results if layer height is .1-.2 mm, but still works with .3mm Works with original screws Tightens FEP film to allow for lower raised height (2-3mm)

Air vent box for ANYCUBIC PHOTON MONO SE using 3M Organic Vapor Cartridge 3311J-100-S1 and 12V Fan AV-F7530MB. You can swap the back panel of the printer with this. 12V can be drawn from the original fan cable inside of the printer. ...I added a DC/DC...

Air vent box for ANYCUBIC PHOTON MONO SE using 3M Organic Vapor Cartridge 3311J-100-S1 and 12V Fan AV-F7530MB. You can swap the back panel of the printer with this. 12V can be drawn from the original fan cable inside of the printer. ...I added a DC/DC...

Anycubic Photon Mono SE SPACER - Wham Bam + Two Trees Flex Plate Spacer Part for Endstop after adding the new magnetic BUILT Plate Here 3 Parts for : - Wham Bam 3,00 mm - Two Trees 2,75 mm (Ali Express) - No Namer 2,50 mm Print in PETG You need to...

Anycubic "Photon Mono 4K" resin vat bottom frame for FEP film. The dimensions fit the standart Photon mono 4k resin vat and standart FEP film. The model was made to replace the factory disposable plastic frame with an improved reusable aluminum...

Replace the FEP film for Anycubic Photon Mono (6.08 inch 2K), after modification, everything is normal and the cost is low. Preparation: Tools: 1. Electric drill 2. Screwdriver 3. M3 drill bit 4. Scissors 5. Wire cutter Material: ...

This is a z stop extension plate for the new version of the Anycubic Photon Mono 4K 2022 version. There is no place to put a spacer on the new printer, so you must print an extension when installing a magnetic bed plate for homing purposes. I printed...

Set the right amount of slack on your Anycubic Mono X, Mono X 6K, and/or M3 Plus FEP with this spacer puck. It was designed with measurements taken from an OEM FEP installation, so achieving proper tension/tuning should be fairly easy. Three files...

Here are my other designs for the Anycubic Mono X 4K ANYCUBIC Photon Mono X Clip On Heater Mount http://www.thingiverse.com/thing:5190198 ANYCUBIC Photon Mono X Z-Axis Bumper Guard http://www.thingiverse.com/thing:5185340 Anycubic Mono X Lid Spacer...

Drip bracket for Anycubic Mono M5s Because of the very aggressive drip angle, if your print is too big, might not fit on the bracket. ...

Please use the attached ZIP Files. ...The STL is only a place holder to upload the .ZIP File . Created from my original Stick delivered with my Anycubic Mono

The device for the printing platform of the 3-D printer Anycubic Photon Mono 2After printing, a large amount of photopolymer resin may remain on the part. To help the resin drain from the part, I developed this device.It is installed in place of the...

The Anycubic Photon Mono requires a z stop spacer to accommodate the thickness of the Wham Bam Flexible Build System. I created a spacer that goes between the z axis carriage and z stop metal tab that triggers the sensor to stop. The original...

I didn't want to wait on a Wham Bam plate because I had prints that needed to get done so I ordered the Sovol plates from Amazon. They had a slightly different height recommendation (2.7mm) so I remixed this adapter in Tinkercad. ...Not only were they...

Wham Bam's magnetic flex plate is awesome but adds 2.6mm to the height of the build plate. Unfortunately, there isn't enough play in the build plate mount so the Z stepper grinds when I home the plate. One option is to print a 2.6mm spacer but I...

This is a R_E_R_F test file for the Anycubic Photon Mono. All the ones I found out there took a while to run, so in the interest of saving time and resin, I created a R_E_R_F file that is heavily inspired by the ResinXP2-ValidationMatrix_200701...

This is a R_E_R_F test file for the Anycubic Photon Mono. All the ones I found out there took a while to run, so in the interest of saving time and resin, I created a R_E_R_F file that is heavily inspired by the ResinXP2-ValidationMatrix_200701, but...

I built the PTC heater for my Mono but I needed a clean way to run the wires out to the power supply. This is a minimal riser that has a 1" gap in the back to allow wires to pass through. You can improve the seal by adding foam, batting, hot glue,...

... made by goyetus. ... It uses: 3 x m3 Nuts. 3 x m3 x 12 16 Magnet 5x5x5 Changed the back plate to use this fan: https://es.aliexpress.com/item/32810655513.html?channel=twinner Added the step file to modify the back as you want.

By downloading User also acknowledges and understands the above and agrees to hold the creator harmless from any and all liability I printed in PETG and here are my settings: Machine: Ender Extender 400x400x500 Nozzle: 0.6 Layer height: 0.48 Line...

I wanted to get a magnetic build plate for my Photon Mono M5, but WhamBam only had it for the M5S. After a bit of research, and determining that the build plates are the same size, I decided to give it a try, and it seems to work perfectly with this...

Thanks to @SnopSnapi for the excellent model and sharing the CAD.  I was  able to import and quickly add some countersunk holes for M3 fasteners to hold the lid more securely.I attached with M3x10 SHCS and M3 Locknuts on the inside of the lid/cover...

refuerzo de paredes