anycubic photon mono x 3d printer

All parts print on Anycubic photon. Because of the slight variations in fan sizes some filing of the inside of the fan box parts may be required. I used Gorilla tape just to make sure the fans were sealed since you are venting the exhaust through a...

Complete Mono X vat drain kit, including stand, funnel, funnel holder and vat holder. Everything prints unsupported on the mono X, 2 prints to print everything. Stand: Use standard European plumbing 15mm copper tube between the connections. *...

Here is the extractor/heater I have made for the Anycubic MONO. I wanted a design with a slim profile that can provide options to extract fume and heat resin caver for the best work temperature. All the plastic parts, should be printed using...

This is a remix of the other Easy-Bed level mods for the Anycubic Photon printer. The last version broke and deformed after a while, so i designed this version, that is a little bit sturdier and features threaded inserts for the Locking screws.One...

This box with a Nikon logo lid holds several SD and CF cards in place side by side.\r\nUpon printing the original design on my photon, I encountered issues - the lid and the box did not fit together properly, the CF section was too small for my CF...

It allows you to vary the thickness of the spacer.After I tried to install this on my Photon M3 it turns out that the original file can interfere with the linear bearing unless you are very careful. ...I have made changes to limit that potential on both...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be 10 of them. The ridges are 0.25mm wide and 0.5mm apart. For each one missing, you are losing 0.25 to 0.50mm of LCD pixels from...

It's compatible with Epax-X1 and Anycubic photon vats, possibly other models as well. I built this using 10mm aluminum pipe for the legs and 8mm pipe for the rotating pins, which I happened to have on hand. The funnel holder is made from M5 screws,...

This is a Remix of Skody01's Anycubic Photon M3 build plate drain. I modified it so that the whole build plate is positioned 15mm further to the rear. Now it will not collide with the cover when the build plate is positioned further upward. ...

I wanted to give it a more personalized feel to this cover so I added the Photon and the Anycubic logo to it. Please notice that the area where the big logo is located is very thin and some might assume is not full uv-proof. I am fine with mine....

I am creating two versions of my rear vent duct adapters for the Anycubic Photon: a 4" version for connecting to standard ventilation tubing and a 2.5" version for connecting to vacuum hoses and smaller tubing. To install, follow the instructions on...

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be exactly ten of them. The ridges are a precise 0.25mm wide and 0.5mm apart. For each one missing, you're losing a significant...

... one of these parts, which includes STL files for both right and left sides. I installed them on both sides of my lid (it looks better that way), replacing one of the hinge screws with M3 x 15mm ones I had on hand, along with washers and Nylock Nuts.

Remixed from https://www.thingiverse.com/thing:3671334 Specially designed for the latest Photon Zero resin printer, this updated model features smaller components, scaled down by 15% to fit perfectly on the new device. ...Additional stand extenders are...

... dimensions. ... Split in two parts, for little printers. IMPORTANT: Due to different scaling values, depending on different slicers you have to calculate your own scale factor. ... As an example: I'm using prusa slicer and scale the parts to 102%

... you to securely hold a 70mm square active charcoal filter just like this one: https://www.amazon.co.uk/gp/product/B074J8515D. ...Whether you're using an FDM or Resin (Photon) printer, you can easily print this adapter and get started with your project.

This is for the ANYCUBIC M3 PREMIUM printer to drain the build plat and prints could not find one that would work so I made my own I added a second hold that as more of a angel on it

However, I didn't want to wait and probably planned to upgrade the factory nut anyway, so I designed and printed a temporary nut for the top of my FDM printer first and then printed this one using the Scad program files modified on the photon. This...

... you! ... This drain arm is designed to go on the platform locking mechanism (locks) and then you insert the platform on the slant, and it will drain into the VAT. This can be printed on FDM and a resin printer, I used 50% infill on an Ender 2 Pro.

standard from the Factory ) i spent almost 4 days with Support and eventually there sending a New Nut - as I didn't want to wait and will probably upgrade the factory nut to something better I designed & printed a temporary nut for the top on my FDM...

SHOULD WORK WITH ANYCUBIC PHOTON S BUT HAS NOT BEEN TESTED FOR IT! ... INSTALLATION: 1) Unscrew the two screw under the plate mount in the front right corner 2) Insert the spacer between the metal plate and the plate mount 3) Retighten the two...

Rear bulkhead of the Anycubic photon is a crucial component that requires precise installation. Two versions are available, one identical to the original and another adapted specifically for the ethernet connector. Key steps include preparing the...

This is designed for straining and collecting debris from anycubic photon vat systems. It can be particularly frustrating to go through the straining process after encountering failed prints, especially when the hardened resin is not visible at all...

This device is designed to be attached to the Anycubic Photon, specifically aimed at reducing the smell from resin use.\r\nA brushless fan with an 80mm diameter should be installed between the panel and the box, secured in place using m5...

Full discloser: This filter system was made by  RJ Maker and here is his links, i just made an adapter to fit it on to the anycubic photon: Original files https://www.thingiverse.com/thing:1305485 and his youtube video that explains everything. The...

Earpiece X-Terra Monitor Single Channel

... this file.</li> <li>Remove the print once complete by pulling up on the support pieces.</li> <li>Go back to printing whatever you want!</li> </ol> <p>The STL, LYS scene, and PWMX file are all present. Use whatever you need. Category: 3D Printers

8mm and 21mm spacers for 92x25mm and 92x38mm fans. ... I haven't printed these yet myself but you can print them on the Photon by printing it vertically.

You might also be interested in these topics: How to calibrate your exposure time: https://github.com/altLab/photon-resin-calibration?fbclid=IwAR06rlwNx4kWLCfTfY1CANumRgU0ohte1M7undZWjIbRVAB_O0DPgniykX8 And the Resin Curing Time Sheet Finder:...