anycubic photon mono fep 3d models

24621 3d models found related to anycubic photon mono fep.
Anycubic Photon Mono FEP film Frame reinforced
Anycubic Photon Mono FEP film Frame reinforced
thingiverse

This is a reinforced 3D printed frame for the Anycubic Photon Mono. ...I have created it when I've broken my original part, and I've figured out that it takes 40 days to get a new one :)

Anycubic Photon Mono FEP film frame
Anycubic Photon Mono FEP film frame
cults3d

Replacement of standart single-use film frame for use common FEP film You need: - 28 countersunk screws M3x6 - 28 nuts M3 - Glue for nuts

Anycubic Photon Mono X - FEP install tool
Anycubic Photon Mono X - FEP install tool
prusaprinters

This is a tool to replace the 13mm thick bottle cap recommended by Anycubic and position it in the middle of the bracket, makes life a bit easier when changing the FEP.Size is 220x145mmYou'll need to make the top surface of the cylinder smooth to...

AnyCubic Photon Mono X FEP installation spacer
AnyCubic Photon Mono X FEP installation spacer
thingiverse

... a cleanly modeled, hollow, and labeled FEP film installation guide tool. Watch the great #TrueEliteGeek FEP install video here: https://youtu.be/33MSMufwN-w Spacer is designed for use on the Mono X, but should work on any 9 inch LCD resin printer.

AnyCubic Photon Mono X FEP installation spacer
AnyCubic Photon Mono X FEP installation spacer
cults3d

... a cleanly modeled, hollow, and labeled FEP film installation guide tool. Watch the great #TrueEliteGeek FEP install video here: https://youtu.be/33MSMufwN-w Spacer is designed for use on the Mono X, but should work on any 9 inch LCD resin printer.

Anycubic Photon Mono 4k FEP stencil
Anycubic Photon Mono 4k FEP stencil
thingiverse

Did you discover the FEP film was incredibly difficult to replace without purchasing a costly pre-perforated FEP? I did. I designed this stencil to solve that problem. ...Simply use some paper clips to hold the stencil in place and cut out the...

Anycubic Photon Mono 4K FEP Upper Ring
Anycubic Photon Mono 4K FEP Upper Ring
cults3d

I broke mine while replacing the FEP sheet. So for now I only have this part. Tried it on a 90mn print, no leaks. I had to widen the holes for the screws, so I redesigned it. ...Please contact me if you notice anything that needs improvement.

Anycubic Photon, Photon Mono FEP film frame removable
Anycubic Photon, Photon Mono FEP film frame removable
cults3d

frame for standard bath photon

Anycubic Photon Mono X Foot FEP  Resin Tank
Anycubic Photon Mono X Foot FEP Resin Tank
thingiverse

Here the foot from the FEP Tank. ... I printed with ASA

Anycubic FEP film frame - Photon D2, Mono, Mono 4k, Ultra
Anycubic FEP film frame - Photon D2, Mono, Mono 4k, Ultra
thingiverse

ANYCUBIC Photon D2, Mono, Photon Mono 4K,Photon Ultra, 2pcs FEP Film frame.

FEP Tool for Anycubic Photon Mono -X
FEP Tool for Anycubic Photon Mono -X
thingiverse

Bitte nicht skalieren ;-)

"Anycubic Photon Mono 4k" resin vat bottom frame for FEP film
"Anycubic Photon Mono 4k" resin vat bottom frame for FEP film
grabcad

Anycubic "Photon Mono 4K" resin vat bottom frame for FEP film. The dimensions fit the standart Photon mono 4k resin vat and standart FEP film. The model was made to replace the factory disposable plastic frame with an improved reusable aluminum...

Replace the FEP film for Anycubic Photon Mono (6.08 inch 2K)
Replace the FEP film for Anycubic Photon Mono (6.08 inch 2K)
thingiverse

Replace the FEP film for Anycubic Photon Mono (6.08 inch 2K), after modification, everything is normal and the cost is low. Preparation: Tools: 1. Electric drill 2. Screwdriver 3. M3 drill bit 4. Scissors 5. Wire cutter Material: ...

Photon Mono-X FEP Spacer
Photon Mono-X FEP Spacer
thingiverse

Spacer for installing new FEP in the Anycubic Photon Mono-X. It would probably work for any 9 inch resin printer FEP spacing. This ensures the FEP has the correct amount of play once it is installed. See how I used it in this video:...

Photon Mono Normal FEP Adapter
Photon Mono Normal FEP Adapter
thingiverse

I just created this thing to use a normal FEP film on a Anycubic Photon Mono, is still a WIP, and I'm not responsible for any damage, leak, or anything that hapens when using this adapter. It worked fine for me, even that it might need a couple...

Photon Mono Stock FEP Replacement
Photon Mono Stock FEP Replacement
cults3d

This is a replaceable FEP mod for the Stock Photon Mono Vat. It uses M3 Screws and Nuts to hold the FEP in place, and seal to the Vat. It uses the same philosophy as the Photon Mono X Vat. Watch the video below to see installation instructions.

Anycubic Photon FEP Calibration Cap
Anycubic Photon FEP Calibration Cap
thingiverse

The Anycubic Photon FEP Replacement Calibration Cap Measures a Compact 48mm x 27mm x 9mm.

Anycubic Photon FEP Cap Spacer
Anycubic Photon FEP Cap Spacer
cults3d

Anycubic FEP Spacer. ...13mm thick and 30mm in Diameter V2 is a little bit smoother

Anycubic Photon Mono X
Anycubic Photon Mono X
grabcad

Anycubic Photon Mono X without inside.

FEP tensioner for Anycubic Photon
FEP tensioner for Anycubic Photon
youmagine

A more refined approach than the bottle cap recommended by Anycubic for tightening or loosening the FEP film during replacement.

Anycubic Photon FEP Cap Spacer
Anycubic Photon FEP Cap Spacer
thingiverse

Anycubic V2 Spacer FEP - A Game-Changing Upgrade.\r\nBoosted to an impressive 13mm thickness and a substantial 30mm diameter, this upgraded spacer sets a new standard for precision and performance.\r\nThe latest iteration boasts an even more refined...

Anycubic Photon Mono VAT
Anycubic Photon Mono VAT
cults3d

Anycubic Photon Mono VAT and Anycubic Photon Mono Frame SLA Printer - Rahmen SLA Drucker by Macyver1174 on Thingiverse: https://www.thingiverse.com/thing:4831934

ANYCUBIC PHOTON MONO HANDLE
ANYCUBIC PHOTON MONO HANDLE
grabcad

Handle for the lid of an Anycubic Photon Mono Resin printer.

Anycubic Photon Mono
Anycubic Photon Mono
thingiverse

A simplified model of the Anycubic Photon Mono printer which will be released soon. Why? ...why not.

Anycubic Photon Mono Vat
Anycubic Photon Mono Vat
thingiverse

Resin vat for Anycubic Photon Mono printer. Use 2.5x16mm screws with a flat head to assemble. ...

anycubic photon mono legs
anycubic photon mono legs
thingiverse

anycubic photon mono legs. ...filament - bflex other accessories: https://www.thingiverse.com/thing:4923162 https://www.thingiverse.com/thing:4912979 https://www.thingiverse.com/thing:4912997 https://www.thingiverse.com/thing:4923146

Anycubic Photon Mono Feets
Anycubic Photon Mono Feets
thingiverse

Everyone with an Anycubic Photon Mono Resin Printer knows it: The Printer slides on a flat Surface. So I made these Feets. I printed them with PETG and attached self-adhesive rubber Feets. ... But I think, when you're able to print TPU or other...

Anycubic Photon Mono Dripper
Anycubic Photon Mono Dripper
thingiverse

A dripper for the Photon mono. ...Designed to be permanently mounted behind the build plate position.

ANYCUBIC PHOTON MONO 4K
ANYCUBIC PHOTON MONO 4K
prusaprinters

I model this replica of the Anycubic Photon Printer, in order to print a miniature.Enjoy!

ANYCUBIC PHOTON 4K MONO
ANYCUBIC PHOTON 4K MONO
thingiverse

SGOCCIOLATORE PER ANYCUBIC