anycubic photon mono build plate 3d models

I have a resin 3D printer, an Anycubic Photon Mono 4K specifically. When I print things, the buildplate remains wet and a lot of resin gets wasted when I remove the part and clean the plate, so i designed this drainer so to make the plate drain...

I did the PlastikJunkies (https://www.thingiverse.com/thing:3006515) fan mod on my Anycubic Photon and decided not to run the wiring through the stock fan location, so I made this block off plate/cover.

I created a PlastikJunkies fan mod for my Anycubic Photon, opting out of routing the wiring through the standard fan slot, which led me to design a custom block-off plate/cover.

ChiTuBox Settings: Z Lift - 0mm (Thanks to Johnson Yeh for suggesting I lay flat on the build plate) Raft shape - None Support - None Support Density - Not applicable Print Settings: Layer Height - 0.02mm Bottom Layer count - 8 Bottom Layer Exposure...

The Anycubic Photon FEP Replacement Calibration Cap Measures a Compact 48mm x 27mm x 9mm.

This adapter replaces the rear exhaust plate of the Anycubic Photon and allows you to connect the printer directly to a standard 40mm vacuum hose. * The other adapter adds a turbine cooler to force air into the tube. Model: Turbine Cooler...

... https://www.thingiverse.com/thing:3006515. ... My part seamlessly integrates on a Anycubic Photon S. Begin by delicately removing the upper plate. Next, carefully unmount the fan and carbon filter. ... Proceed to solder the wires with the new fan.

Screw the hanger into the hanger mount USE: Build plate slips in using a friction fit For re-leveling the build plate, you can remove one of the bolts (i found the rear one works best) and tilt the hanger finger upwards. You should then have plenty...

A safeguard against accidental shutdown of an Anycubic Photon 3D printer. Additionally, the USB drive is now more secure against outside interference. ... Idea from: https://www.thingiverse.com/thing:3422406 www.deepl.com

Remix opens the front face to reduce the amount of supports required in printing and enlarges the interior slot by 3mm to fit the Anycubic Mono 4k.

This is an OpenSCAD version of the original Anycubic Mono X Wham Bam Z axis spacer by Elantris. ...It allows you to vary the thickness of the shim.

I made it for anycubic wash&cure using photon zero resin printer. maybe you have to fine proper bolt and nut. refer following video. ... https://youtu.be/GewI4NBa6AQ

This is an air purifier for the inside of a Photon Mono X(Photon mono X 6K) 3D printer It needs two fans with dimensions of 6 * 6 * 1.5 cm 12 V And some activated carbon for its 10 cm tank Requires a 12 volt adapter Purifies up to 95% of resin odor...

This is a basic handle for the Anycubic Mono X. Use 3M double sided tape to adhere to the lid. Sand the bottom of the printed handle for better adhesion. I used 3M auto adhesive tape. ...

This is a basic handle for the Anycubic Mono X. Use 3M double sided tape to adhere to the lid. Sand the bottom of the printed handle for better adhesion. ... I used 3M auto adhesive tape.

Quick and dirty ... ...found nothing for the cheap Mono SQ (got mine for around 100€) ... hope we will se more parts for this model in the future as they were cheap on sale by Anycubic.

Inside the MONO X the Z-Axis extrusion penetrates the plate and leaves a gap just below the lid sensor - if this isn't sealed fumes from the build area are pulled down by the fans housed in the base and are explelled into the room the printer is in....

This is a remake of https://www.thingiverse.com/thing:3520264. ...I adapted those feet to match the Anycubic Photon rubber feet, resulting in a substantially quieter printer and workspace due to reduced motor vibration and table resonance.

Washing machine for Anycubic Photon S with support for 3d printer table attached directly to the capOn the bottom of the tub just buy a USB dishwasher to wash the piece

A stylish sillouette of the famous AnyCubic Photon 3D printer. This can be created as a pendant, earring, brooch, tiepin, cufflinks, etc. and painted in a range of metallic tones for a glamorous finish. ... #ANYCUBIC3D

Anycubic Photon S screen seal Stops resin spills get into the machine. You will need to use a vinyl cutter to make it. ... After installation, you will need to relevel and add -.1 to the level

This mod allows for an installation of an Noctua NF-A4x20 FLX (40mm) fan in your Anycubic Photon printer. ...This is primarily because the original fan had an bearing failure and was obnoxiously loud.

Anycubic Photon Parallel Led array for Parallel UV Light Source from Chitusystems. Different type of body, not like on the picture. https://www.chitusystems.com/product/5-5-6-0-inch-parallel-uv-matrix-led/ For installation in the Photon case. ...See...

These allow you to use "Workhorse Safety NIOSH P100" filters (The adapter seems a little different from the 3M adapter.) to assist in cleaning air for the Anycubic Photon Mono X. It all does limit the airflow, but ideally improves the air quality. ...

Hose adapter was used from Anycubic Photon Air Vent System by Creative-Process https://www.thingiverse.com/thing:3318738 Corrugated panel was used from Corugated iron by stewartmiller https://www.thingiverse.com/thing:2364932 2200 RPM...

Two easy solutions to eliminate hazardous fumes from your space when operating the Anycubic Photon.\r\nOne option involves installing a removable ventilation unit at the back of the printer using screws instead of the standard factory-installed cover...

just a holder for the build platform of my Photon 4K holds it at an angle to getter a better resin runoff to the vat

This is an OpenSCAD version of the original Anycubic Mono X Wham Bam Z axis spacer by Elantris. ...It allows you to vary the thickness of the shim.</p><p>The original model can be found here: <a...

This is a bottle drainer for the Anycubic Photon M3 Plus. The lid can be put back on while using it to protect the resin from dust and light. This can be left in place after use without interfering with the print process. The bottom slot is 40mm x...

This unit is made to pre-heat the Anycubic Photon printing chamber, this can be very useful fi you for example have your printer located in a cold place, but also to get your printer to a precise temperature to obtain better print quality, especially...