anycubic photon mods 3d models

I designed a compact, elegant base for my Anycubic Photon S that integrates a replaceable carbon filter and tool storage. Most solutions I've seen online are these gigantic 4 inch diameter carbon filter units designed for much larger machines, and I...

Please use the attached ZIP Files. ...The STL is only a place holder to upload the .ZIP File . Created from my original Stick delivered with my Anycubic Mono

Drip bracket for Anycubic Mono M5s Because of the very aggressive drip angle, if your print is too big, might not fit on the bracket. ...

I had to replace my Photon S screen and after doing some searching I found the original file by Bart127. The only issue was due to my using a Snapmaker Original I didn't have the build space needed to print the spacer. After remixing, just cutting...

Additionally, it features an XT60 power connector that powers both the Photon and a 100w chamber heater efficiently. When printed in PETG, the XT60 fits snugly, although you may need to enlarge it depending on your material and printing tolerances...

I wanted to get a magnetic build plate for my Photon Mono M5, but WhamBam only had it for the M5S. After a bit of research, and determining that the build plates are the same size, I decided to give it a try, and it seems to work perfectly with this...

Replacement foot/peg for the Mono X vat. ...Use E6000 to adhere new peg in the hole.

A Revolutionary Scent-Free Tower: Empowering a Fresh Environment with Active Carbon and Joyful Printing

Additional handle for wash & cure machine. It allows you to conveniently open the machine with one hand and reduces the dirt on the cover. ... The handle should be glued with double-sided tape.

Replacement of standart single-use film frame for use common FEP film You need: - 28 countersunk screws M3x6 - 28 nuts M3 - Glue for nuts

This holds 2x VATs (blue and black). Print with a darker color to deter sunlight. Use PETG filament for the door hinge 'bolt'. I've included the Fusion360 file for easy customization. Kindly leave a like or whatever.. ...LOL.

I had some aluminum poles (2 of 200.30 mm and 2 of 100.40) so I made another stand for the vat holder that samuelemarazzita made.I modify the holder of the vat so the poles fit, the rest its my design, 2 M4 screws made the funnel base adjustable.

This is a revised version of the platform bracket provided by Elegoo. It helps a lot when removing the model from the build platform because it allows the resin to flow into the tank. Just unscrew the platform from the holder, insert the "Platform...

A versatile funnel that securely fits onto large 1-liter bottles, allowing you to pour a whole vat or other bottle for filtering without spilling or having to juggle the paper filter. ... If you appreciate my designs, consider supporting me on Patreon:...

This bracket holds the build plate vertically over the vat, tilted slightly forward and inward to recover resin drip at one corner.

I have to assume there are more crazy people like me that just hate to see the resin sitting on the build plate bracket. I printed and started using the Scraper by Oggie referenced in this remix, but i adjusted the sizes of his scraper and put new...

I broke mine while replacing the FEP sheet. So for now I only have this part. Tried it on a 90mn print, no leaks. I had to widen the holes for the screws, so I redesigned it. ...Please contact me if you notice anything that needs improvement.

For top and bottom print two pieces, also you need 4 x M3 screews. ...

This is a simple bracket for holding the build plate at a slight angle so that the resin can drain away more easily after a print.

<p>We printed ours in our Black ecoPLA Tough filament at 0.2mm layer height and 100% infill<br><br>** ONLY SUITABLE FOR 0.5L BOTTLES **</p>

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

This simple attachment allows for the build plate to be attached to the z axis after printing to allow for and ideal height and angle for resin to drip.  Caution: The connector fits relatively snuggly, but is not a perfect fit, so I advise using...

Wide stand for better sustainability. ... I recommend using glue to connect all parts.

For top and bottom print two pieces, also you need 4 x M3 screews.

This holds 2x VATs (blue and black). Print with a darker color to deter sunlight. Use PETG filament for the door hinge 'bolt'. I've included the Fusion360 file for easy customization. Kindly leave a like or whatever.. ...LOL.

The part fixes the build plate at a steep angle for good resin runoff.

simple remix to Daniels build to fit the new version of the mono 4k since they made some changes to the gantry and now has different dimensions. ...This is for the model of printer that has black metal gantry made from folded/molded gantry.

With the drip stand you can let the resin vat drip out in peace. All you need in addition is a 10mm thick rod (d=10mm r=5mm). ...I used a wooden stick and glued everything together with super glue.

Did you buy the most affordable SLA / resin printer? Did you discover the FEP film was incredibly difficult to replace without purchasing a costly pre-perforated FEP? I did. I designed this stencil to solve that problem. ...Simply use some paper...

I looked for a drip bracket on thingiverse and did not find one so I made one myself with help from a friend. The fit on the lift mechanism is quite tight I would maybe shave of 0.5mm off from one of the long inside parts. But some sanding did the...