anycubic photon mods 3d models

(See image 1 for motor mod)image 1For converting a plastic 180 to a 360 servo, open it to reveal the gears, on the top most gear you can find a small nudge that prevent it from rotating 360, take a flush cutter and break that nudge. This will make it...

I am hoping that with these mods I will be able to print at the same (or better) quality but at a far higher speed than the standard Cura settings. There are no shortage of upgrade designs on Thingiverse (and other sites), but finding the best ones...

This is a simple mod for your MK3 to use it as a penplotter. The main design objective was for it not to interfere with printing and to not have to assemble or disassemble any parts to change from one to the other.</p><p>I tested multiple designs...

This control box could be used with other printer's with some mods for the control board hole positions and the LCD panel to make it fit. This is a well ventilated control box to fit both the LCD panel and the PCB board, but not the power supply. The...

Constant testing and printing are underway with mods on nearly every model, wasting over 300 feet of filament in the process. I'd appreciate support for my project as it's not intended for non-3D users but rather for those who want to quickly build a...

Post-Printing: Check the clearance between the belt and the block How I Designed This: Although I've been using the printer for more than a year, I only realized that the belt was rubbing against the housing several months later, after I saw a video...

There are a couple of options:Adjust the print area: use NotePad or other text editor to create a gcode file with the following then copy it to your USB Flash drive and run it like any other print file.&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ; Set XY...

Changed the shaft part to accomodate the shaft with grease nozzle.Deck: used the access hatch by simon5492 but modified the cover to go over/around the box instead of sitting on it.Cabin: changed the sidelights to a smaller backplate and added hole...

The brace will help stabilize the frame and the added room gives you enough space to easily run a 330x330mm hot bed surface. For this mod, you will need to purchase: • 2 - 7/16-14" x 36" Steel Threaded Rods -...

This can burn your house down if done incorrectly!Do not attempt to build this unless you are familiar with:SolderingLiIon battery safetyBasic electrical engineeringNow with added STEP file for remixing.Print SettingsPrinter:Modded...

The Mount for the Insta360 OneR that really protects your oneR (4K mod) on your freestyle or race quad! The lens bumper does not show up in the footage, recording light is clearly visible from the front, and the screen is easy to operate - if the...

One fan or two, I prefer two for better airflow.\r\n\r\nDon't forget: your warranty will be void by doing this mod.\r\n\r\nI had already put some 60mm noctua fans in my control box (to replace the 50 and 40mm), cut all the crap in front of the fans,...

I recommend using a hand-drill with a 2.7mm bit to manually drill out the holes prior to assembly.Step 3: Final AssemblyThe keyboard sub-assembly should be assembled with the following steps:Lube, mod, and install the stabilizers.Install the switches...

If you want to run LEDs and an Octopi off the same psu you need to upgrade. One of my many mods to the printer was to get a Mean Well LRS-350 24v psu which is the successor to the NES-350 24v, the only real difference being reduced cost (about $20...

Please feel free to print, mod and share your builds with the hashtag #NLR35.NLR35's key features are:- 2 camera mounting options- analog or digital FPV link- ELRS long range RC link- 1s 12A AIO board- top or bottom battery mounting- push or pull...

To top it all off I added the 5015 hotend cooling mod by CJLAW1611 posted on cults3d. This system is build on top of a my own remixed version of the BiQU linear rail mount by Schwab_Manufacturing_Solutions. I cut down the backplate and added...

BOM (bill of materials): M4 nuts and bolts A good quality SSR (carefully select the part as there are a lot of counterfeit items) A selection of ring terminals for cable ends (yes you need to cut your printer wires) Two springs (used to push the SSR...

Print Settings Printer: Heavily modded Craftbot Rafts: No Supports: Yes Resolution: 0,15 or 0,20 mm Infill: 33 or 50 % Notes: Print both models in PETG with 3 mm thick walls and slightly hotter than usual, this should give you enough strength for a...

This mod gave me, with a clone Titan extruder, and clone V6 hotend, 145mm of vertical height. I can push that to around 155mm, if I don't home the axis before lowering it, and I choose to lose ~30mm of X. Bonus For Z, I have included an end stop...

The barrels of different lengths are interchangeable and thus offer a cheap platform for modding. The project will make further progress in the near future. If the project meets your interest, there will be a Discord and YouTube videos. Ziel...

****After modifying a couple prototypes with suggested mods (one with a lip, and one with a top-mount line ring) I found them to have terrible action, either fighting the lip or fighting the line holder. I'd recommend adding weight to the front of...

The next problem is that the heated bed won't get to 90 degrees C without modding the drive voltage. Luckily this is simple and takes about 5 minutes: just take the back off the control box, loosen the four large screws underneath it, and slide the...

... Unless you are using transparent filament this is not a necessity. The base is the functional part of this set.&nbsp;Printing one pair at 0.30mm layer height will take about 23m&nbsp;Here's an example video of putting the tea light mod together:

Note: The project relies on "stock" LED mod already installed, mostly for holding cables in place and also integrates with the wiring for LEDs to save on space. It can be done stand-alone without LED strips as necessary. Note 2: I'm partial about...

no mods needed. but keep in mind you need a plug to close off the air supply form your cyclone feed. otherwise you will have a air leak.</p> <p>and of course you still need a spring and 2 pins to complete the mag release</p> <p>note: these have been...

There are a lot of ways to mount stuff: 3D builder in Windows 10 is an easy way to make basic mods to a file if you aren't happy with my options (add holes, stretch parts etc.). This is a generic mount kit for my RC crawler bumper projects. It's...

Human: ** Kyosho Blizzard FR Dual 540 Motor Transmission **\r\n** * Works with SR, FR and FR 2.0 versions for sure, possibly others **\r\n\r\n* NOT compatible with standard plow lifting mechanism\r\n* Compatible with my modded plow :...

If you really want reverse and are willing to add to the project cost consider a bidirectional esc like this:...

Will work with most other mods! You can see the [CR Series Y Axis Screw here](https://www.thingiverse.com/thing:4039877) and the [CR Series Octoprint ready SKR conversion here](https://www.thingiverse.com/thing:4130769). #[Come hang out get...

... others would appreciate it. *****IMPORTANT***** If you decide to use this, you will likely also have to raise your bed to avoid losing around 3cm of build space on the y-axis. Raise the bed using this mod: https://www.thingiverse.com/thing:3890803