anycubic photon mods 3d models

This box with a Nikon logo lid holds several SD and CF cards in place side by side.\r\nUpon printing the original design on my photon, I encountered issues - the lid and the box did not fit together properly, the CF section was too small for my CF...

You can print it on your photon mono, or on your traditional FDM printer :) Here is a simple to use and easy/quick to print holder for your Anycubic photon mono printer (4K in my case). All you have to do is remove the top knob, insert the holder,...

Designed in Fusion 360 This backplate is precision-engineered to provide a secure fit on the Anycubic Photon Printer, ensuring smooth and hassle-free operation. The design takes into account the printer's unique geometry, guaranteeing a perfect...

With this you can be sure you only throw away absolutely empty bottles :) This was made for Anycubic Photon Mono 4k - I don't have meassurements of any other models to confirm if it would work there. Feel free to remix for your model. It was also...

Orientation with 30% infill and 30° overhang limit supports that worked for me included in 3mf.Doesn't have to be removed to also use model it was remixed off https://www.printables.com/model/236478-anycubic-photon-mono-x-6k-build-plate-hanger. ... I...

I was looking for a cover for my vat but only have my Anycubic Photon Mono 2 (no filament printer).All the lids I found were to large (even angled).So I used Tinkercad to remix one.I split one in half, added some height to the center, and then added...

Couple brackets for the Anycubic Photon Mono X's power supply. Print 2. Install screw through bracket, there's a hole for a screwdriver. Recommend scaling up maybe 2-3% because I made it too tight. ...Screws are #6.</p> <h3>Print Settings</h3>...

It allows you to vary the thickness of the spacer.After I tried to install this on my Photon M3 it turns out that the original file can interfere with the linear bearing unless you are very careful. ...I have made changes to limit that potential on both...

This is a Remix of Skody01's [Anycubic Photon M3 build plate drain](https://www.thingiverse.com/thing:5674605). I modified the inclined holder to also incorporate a slight angle (7.5°) towards the back, so that the resin flows towards only the left...

This is designed for a window guide width of 1.1inch see picture and a 3inch exhaust duct.  These parts are designed to be printed on the Anycubic Photon printer.  I suggest printing with ABS resin.  Additionally the parts are designed to be a...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be 10 of them. The ridges are 0.25mm wide and 0.5mm apart. For each one missing, you are losing 0.25 to 0.50mm of LCD pixels from...

Riser for the Anycubic Photon M3 lid to allow passage of a small power cord in the back left corner. Useful for things like heaters, air cleaners, etc. Print the single piece if you have a big enough printer. It has also been split into four...

... the center of the cover to act as a handle for easier removal. The tolerances are tight, but you can place the cover on the vat and remove it without needing to remove the resin vat from the printer itself. This fits the original anycubic photon.

This base allows for easy venting of the Anycubic Photon S into a 4" duct, enabling exhaust into a charcoal filter or outdoors. The Anycubic Photon S lacks an easily replaceable vent grill like its original counterpart. This new base is designed to...

I just bought an ANYCUBIC Wash and Cure Station and noticed that the buildplate Adapter is only for the old ANYCUBIC Photon. ...So I created an adapter fpr the ANYCUBIC Photon Mono.

Adapter for Photon Mono buildplate to mount on Anycubic Wash & Cure Station. Uses M6 screws, like the original. I used a height of 15mm instead of 12mm of the original mount on the Photon Mono. It makes everything a bit more stable and for me...

Another version of the great “ANYCUBIC PHOTON Easy Leveler” by wundel https://www.thingiverse.com/thing:3096818. In this review, only two improvements are notable - pressure springs have been included to avoid holding the plate in place with your...

**https://www.printables.com/model/643200-anycubic-photon-mono-2-vat-cover** Made a vat cover/lid for the new *Photon Mono 2* since i couldn't find one. Enjoy. There are two models: one titled **VASE** and one titled **RIGID**. The **RIGID**...

Another Version of the Genius “ANYCUBIC PHOTON Easy Leveler” by Wundel https://www.thingiverse.com/thing:3096818 In this Review, Only Two Improvements Are Made - Pressure Springs and Insert Positioning The only improvements made to this design are...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be exactly ten of them. The ridges are a precise 0.25mm wide and 0.5mm apart. For each one missing, you're losing a significant...

I wanted to give it a more personalized feel to this cover so I added the Photon and the Anycubic logo to it. Please notice that the area where the big logo is located is very thin and some might assume is not full uv-proof. I am fine with mine....

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

An Anycubic Photon vat holder is designed specifically to drain resin back into the bottle. The center of the vat should sit directly in the middle of a 1-liter bottle, with the bottle pushed up against the Skadis pegboard. A unique attachment on the...

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

I know, there are some vent systems for the Anycubic Photon already available but I didn't find one that includes a rear fan, which is why I designed this one. ... What you need: * 1 - 92x92x14 mm fan (Noctua NF-A9x14) * 4 - M3 x 16mm socket head cap...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

Temperature controller for Anycubic Photon S (probably works with other versions too). Required parts: PTC Heating Element: https://www.amazon.ca/gp/product/B07FJW1DG3/ Temperature Control Module https://www.amazon.ca/gp/product/B08FDTZF3Q/ ...

It's compatible with Epax-X1 and Anycubic photon vats, possibly other models as well. I built this using 10mm aluminum pipe for the legs and 8mm pipe for the rotating pins, which I happened to have on hand. The funnel holder is made from M5 screws,...

This is my own try to make the vat for Anycubic Photon Mono X, since I wanted to make a drain stand for the Vat. I dont claim that it is totally exact as the original but as close as possible I could make it. If anyone finds anything wrong with it...

Crafted specifically for Anycubic Photon printers, this platform accommodates the resin tanks seamlessly. Once printing is complete, simply slide the tank into place, shielding the lower area from splashes, scratches, and dust. This way, you can...