anycubic photon m3 fep 3d models

Blocks to hold the cover in place! ... if you use an optional seal or not....hold cover in place.. The inspiration comes from my Anycubic Wash&Cure Plus...

\- M4 x 25mm screws (2), M4 hex nuts (2) (I got away with using M4 x 30mm screws) \- M3 x 15mm screws (4), M3 hex nuts (4) \- [activated charcoal sachets](https://www.amazon.com/dp/B0149GP7IU?psc=1&ref=ppx_yo2_dt_b_product_details) (2) (optional)...

Drainer for Anycubic M3 MAX tray. To print in FDM. ... Allows you to tilt the print bed so resin can flow into the tray before removing prints

Couldn't find a buildplate drain bracket for the Photon Mono SE that can be left on during printing (it seems like the regular Photon buildplate attachment is really close in size but I'm not sure). Holds buildplate at an angle so all the resin drips...

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ...The distance from gap to gap on the lid is 15.2 cm.

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ... The distance from gap to gap on the lid is 15.2 cm.

... you to securely hold a 70mm square active charcoal filter just like this one: https://www.amazon.co.uk/gp/product/B074J8515D. ...Whether you're using an FDM or Resin (Photon) printer, you can easily print this adapter and get started with your project.

However, I didn't want to wait and probably planned to upgrade the factory nut anyway, so I designed and printed a temporary nut for the top of my FDM printer first and then printed this one using the Scad program files modified on the photon. This...

i desing this angled cover inspired from @scottyujan desing but his was to big for my 3D Resin Printer so it's a smaller piece that works better for my Photon Zero printer. ... i suggest fliping the 3d model to a 90 degree angle for easier printing...

This is the holder for a portable heater I use in this video to keep the ambient warm during winter for my Photon. https://youtu.be/sLqAOGNk40s Can be used in other models and other positions, just ignore the plate STL. ... Recommend using PETG or...

Remixed from https://www.thingiverse.com/thing:3671334 Specially designed for the latest Photon Zero resin printer, this updated model features smaller components, scaled down by 15% to fit perfectly on the new device. ...Additional stand extenders are...

This is a support for avoid to find a free place for the top cover. ...It simply hang to the printer itself. Printing: PLA, no spécial think. Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/

grip for anycubic photo mono x or wash and cure using with suction cup https://fr.aliexpress.com/item/4000599710014.html?spm=a2g0s.9042311.0.0.3a566c37Fx2vFs rotate to 90 on x

German: Resin Tank Halter für den Anycubic Poton mono 4k. Es gibt zwei Versionen des Auslegers, der Halter passt nur auf die im Bild oben gezeigte Version. Der Halter kann liegend, mit Support an dem Langloch oder stehend gedruckt werden. Resin...

It simply hang to the printer itself.Printing: PLA, no spécial think.Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/Print...

... Easy to print (just check the picture for correct orientation), and if you're using a photon, don't forget to hollow out the parts to save on resin. The funnel with filter I'm using is made from silicone - just expose it to UV light to clean it.

For top and bottom print two pieces, also you need 4 x M3 screews. ...

For top and bottom print two pieces, also you need 4 x M3 screews.

I designed a 3-inch exhaust port adapter, allowing me to connect the photon to my existing exhaust fan and safely vent it outdoors. The 3-inch front lip requires additional reinforcement, but that's the only part in need of support. ...If you can't...

... use with a hose featuring an inline fan. ... This design is tailored for use with the Photon S, and might necessitate some foil tape to ensure proper seating. ... The results are outstanding; this setup almost completely eradicates any lingering odors.

This lid also WORKS with Photon Mono -V3 fix overall fit (needs a well-tuned printer so print fits properly) -V2 fix corners and other small details -Add no logo version This resin vat lid keeps dust and other debris out of your resin tank and also...

* Connect the fan directly to the internal fan, either by cutting and connecting wires in parallel or by accessing the "MB F" green connector on the Anycubic board. * Remove the rear vent cover and secure the smoke extractor in place using the same...

So i'm loving my Photon M3 Max autofill/autofeed feature with the exception of the cap. Its built in a way that it wouldn't be very easy to move the parts over to a new customized cap and i find myself using Siraya Tech resins almost exclusively as...

So i'm loving my Photon M3 Max autofill/autofeed feature with the exception of the cap. Its built in a way that it wouldn't be very easy to move the parts over to a new customized cap and i find myself using Siraya Tech resins almost exclusively as...

I'm having trouble keeping a firm grip on the tank and filter as I pour the resin back into the Anycubic resin bottle. To make things easier, I came up with this handy solution! ... Edit: August 27th, 2018 - I added some fun by attaching a tea strainer...

The upper brace for the lead screw on my Anycubic Mono X was seemingly missing a bearing and the lead screw was not secured properly because of this. This is a simple design to remedy the problem. ... If printed out of filament you will definitely need...

The upper brace for the lead screw on my Anycubic Mono X was seemingly missing a bearing and the lead screw was not secured properly because of this. This is a simple design to remedy the problem. ... If printed out of filament you will definitely...

Hello, Here is a support for the resin tray of the anycubic mono X. For this you just need the desired length (I have 370mm for the example) A tight fit has been made between the parts and the profile, to avoid screws! ... Here is the reference to...

One of the things I miss about the original photon was how easy you could rotate the bed by 90 degrees after printing to allow hollow parts to drain fully, this design achieves the same thing but at a angle of 88 degrees to keep the top of the build...

However, be aware that these designs won't fit neatly on the base of the photon due to increased length. By setting the X-scale to around 70%, you can make it fit within the working area, although it will appear slightly narrower than the tray...