anycubic photon m3 fep 3d models

Rear bulkhead of the Anycubic photon is a crucial component that requires precise installation. Two versions are available, one identical to the original and another adapted specifically for the ethernet connector. Key steps include preparing the...

This is the DIY carbon filter for Anycubic Photon Mono SE. It should reduce some resin fumes.The factory carbon filtration of Photon Mono SE doesn't work quite well. Two fans push fumes from build area through the activated carbon sponge to the...

... However, this problem can likely be resolved by not fully closing the front lid during ventilation operation. The lower section of this component features four holes for m3 thread cutting, enabling secure internal attachment via the photons lid.

Simple angled Photon Mono Build Plate holder. ...Heavily inspired by this design for the Photon Zero: https://www.thingiverse.com/thing:4224960 Modeled in TinkerCAD.

I've printed different drainer for the Photon but no one fits on my Photon Mono 4K. ... So i designed this one.

Full discloser: This filter system was made by  RJ Maker and here is his links, i just made an adapter to fit it on to the anycubic photon: Original files https://www.thingiverse.com/thing:1305485 and his youtube video that explains everything. The...

Wanted a lid to cover the resin vat of a Photon Mono SE.

Simple damper feets for Photon Mono 4K (maybe also fit on a regular PhotonMono)

A knob for the build plate on the Photon Mono X

All parts print effortlessly on Anycubic photon. Due to slight variations in fan sizes, some filing of the inside of the fan box components may be necessary. I used Gorilla tape to ensure fans were securely sealed since exhaust ventilation occurs...

This system extracts fumes from an Anycubic Photon printer without replacing existing panels. Instead, it attaches to the rear of the printer over the top of the rear vents using magnets, preserving warranty validity and ensuring easy attachment and...

All parts print on Anycubic photon. Because of the slight variations in fan sizes some filing of the inside of the fan box parts may be required. I used Gorilla tape just to make sure the fans were sealed since you are venting the exhaust through a...

All parts print on Anycubic photon. Because of the slight variations in fan sizes some filing of the inside of the fan box parts may be required. I used Gorilla tape just to make sure the fans were sealed since you are venting the exhaust through...

*Original Summary* This is my re-creation of the Anycubic Photon MonoX build plate / attachment, the areas I needed anyways. I am going to make some TPU parts for it, so that the resin doesn't get all in the bolt area, crevices, etc. Makes it a...

I needed a vent adapter for my new Anycubic Photon Mono X and didn't like the ones already here with the vent pointing straight back so i chose to make my own that's angled to the side. So far there's 4 versions, with differences in screw length and...

Based on a bad experience I had, I have created this protection bar for the Anycubic Photon Mono X Axis. I had an accident where I spilled resin, and it ran down the central axis and jammed the stepper motor. I thought it was damaged because it...

This is a remix of the other Easy-Bed level mods for the Anycubic Photon printer. The last version broke and deformed after a while, so i designed this version, that is a little bit sturdier and features threaded inserts for the Locking screws.One...

Based on a bad experience I had, I have created this protection bar for the Anycubic Photon Mono X Axis. I had an accident where I spilled resin, and it ran down the central axis and jammed the stepper motor. I thought it was damaged because it...

I tried to install a magflexplate system ( https://www.magflexplate.it/ ) on my Anycubic Photon D2. Problem was the system has an overall hight of 4,5 mm and the printer does not allow to set the zero parameter above the endpoint of the rail. The...

There seems to be no hanger for photon mono 2 existing in Thingiverse at the moment, so I created this.

#Description# This is a longer z-stop flag for the Anycubic Photon Mono 4k with the newer version of the build plate arm which has a curved back where it mounts to the z-axis carriage. This z-stop flag is 4mm longer than the original metal piece,...

The Anycubic Photon S top cover design is fragile and susceptible to cracking or shattering near the hinge, unlike its predecessor. The top cover should never be allowed to open 180 degrees, which puts excessive strain on the thin plastic frame. My...

Wash machine for Anycubic photon mono. Designed to fit any plastic container you can buy. To adapt to your container, you need to measure its width and depth, and then scale the "bearing_axis_(scalable)_2psc.STL" part according to the measured values...

Simple vat cover for the Anycubic Photo Mono M5s resin printer.

this will allow you to pop the sensor up and out of the rail (do not remove fully or pull out farther than needed!) Remove the rear cover and 4 M3 bolts on your Photon (obviously make sure your vat is removed first) Access the 4 M4ish bolts that...

8mm and 21mm spacers for 92x25mm and 92x38mm fans. ... I haven't printed these yet myself but you can print them on the Photon by printing it vertically.

... The connector fits relatively snuggly, but is not a perfect fit, so I advise using caution while setting it on the Z axis attachment. If not set securely, a large impact will cause it to drop off into the resin and potentially harm your FEP or LED.

I just bought an ANYCUBIC Wash and Cure Station and noticed that the buildplate Adapter is only for the old ANYCUBIC Photon. So I created an adapter fpr the ANYCUBIC Photon Mono. ... Update 01.12.2020 I added a smaller variant for larger prints.

If you are greedy like me you can use this extension to grab any single drop from Anycubic bottle resins ;)

If printing is complete，Use this will save resin Did a nice logo on the file added the .Photon file with supports :) remix from https://www.thingiverse.com/thing:2930511/files